ELETTROQUADRI MP3 Скачать руководство пользователя страница 5

Страница: 5 / 66

General information

© ELETTROQUADRI S.r.l.

5 / 66

INSTALLATION MANUAL

GENERAL INFORMATION

1.1.

Installation Manual

The Installation manual is an integral part of the board and must be kept with care and accompany the board

throughout its entire life cycle, right up to final scrapping.

The manual has been drawn up by the Manufacturer to provide all the necessary information to those authorized

to interact with the machine during its expected service life: buyers, installers, expert operators and specialized

technicians.

ELETTROQUADRI S.r.l. declines all liability for improper use of the board and for damages caused as a result of

operations not considered in this manual or in any case unreasonable.

1.1.1.

Reproduction limits and copyright

Reproduction of the manual, even partial, and distribution by any means, unless expressly authorized by the

Manufacturer, is prohibited.

Any unauthorized reproduction will be prosecuted in the manner and times prescribed by the laws in force.

Reprinting, reproduction and translation, even partial, are prohibited without the written authorization of

ELETTROQUADRI S.r.l.

The manual cannot be transferred to third parties for viewing without the written authorization of

ELETTROQUADRI S.r.l.

1.1.2.

Updates

Illustrations of the board are provide for explanatory purposes only and are not binding for the Manufacturer.

The manufacturer reserves the right to make any changes to components, parts and/or supplies for the purpose

of making improvements or for any other reason, without having to update this manual unless said changes

alter machine operation and/or safety.

IMPORTANT

The Manufacturer reserves the right to make changes without prior notice.

IMPORTANT

Any additions to the manual which the manufacturer deems appropriate to send to users must be

kept together with the manual, becoming an integral part thereof.

ELETTROQUADRI

SINCE 1983

MP3

Содержание MP3



































































Результаты поиска

Содержание MP3

Отзывы:

Похожие инструкции для MP3

Бренды по названию

Популярные бренды

ELETTROQUADRI MP3, Руководство по установке

Результаты поиска

Содержание MP3

Отзывы:

Похожие инструкции для MP3

Бренды по названию

Популярные бренды