10
WELDING
steel,
on, or copper using the TIG procedure. Connect the earth
the positive pole (+) of the welding
achine, and the clamp to the workpiece as close as
from the cylinder pressure
achine.
t the mode
and
V
and the welding parameters
w of inert gas must be set to a value (in
t be 4 to 6 times the diameter of the electrode.
M
the electrode (Ex. diameter 1.6 x
sses for up to 75A, and D.I.N. 11
parameters only after welding.
ressing the push-button W briefly makes a selection;
more than 3 seconds, it saves the data.
ach time it is turned on, the machine always shows the
on, the display shows the
ymbol
PL
; this disappears after 5 seconds, and a working
in paragraphs 3.2
ave the data in the
ps flashing: at this point, the data have been
u wish to save in a program other than
P01
,
the next rime the machine is turned on.
he operator may edit and save a selected program by
uttons
C
and
V
and select the welding
ected, activate the
I
, and set
ich are
reviously selected program, press the
r stops
ssing the push-button
W
, then hold down the
eginning with a previously saved program, the operator
te the program itself,
select the parameters to
t them.
for more than 3 seconds, until
d (program symbol changes from
ew program
select the parameters to
r
W
until the desired program is
mbol changes from flashing to steady).
ols may be connected to adjust
e welding current for this welding machine:
)
neously connect the
lding current from the minimum to the
the maximum.
3.5 TIG
This welding machine is suitable for welding stainless
ir
cable connector to
m
possible to the welding point, making sure there is good
electrical contact.
Connect the power connector of the TIG torch to the negative
pole (-) of the welding machine.
Connect the torch connector to the welding machine
connector
Y
.
Connect the torch gas hose fitting to the fitting
X
on the
machine, and the gas hose
regulator to the gas fitting
A4
on the rear panel.
Turn on the m
Do not touch live parts and output terminals while the
machine is powered.
The first rime the machine is turned on, selec
using the push-buttons
C
by means of the key
I
and the knob
P
as described in
paragraph 3.2 The flo
liters per minute) approximately 6 times the diameter of the
electrode.
If you are using gas-lens type accessories, the gas
throughput may be reduced to approximately 3 times the
diameter of the electrode. The diameter of the ceramic
nozzle mus
The most commonly used gas is normally ARGON, because
it is less costly than other inert gases, but you may also use
blends of ARGON with a maximum of 2% HYDROGEN for
welding stainless steel, and HELIUM or ARGON-HELIU
blends for welding copper.
These blends increase the heat of the arc while welding, but
are much more expensive.
If you are using HELIUM gas, increase the liters per minute
to 10 times the diameter of
10= 16 It./min of Helium).
Use D.I.N. 10 protective gla
from 75A up.
3.6 SAVING
You may save
P
held down for
E
last welding condition used.
3.6.1. Saving data from the PL program
Using the machine for the first time
When the machine is turned
s
current is displayed. Follow the instructions
and 3.5, then proceed as follows to s
program
P01
:
• Briefly press the push-button
W
the message
P01
will
appear flashing.
• Press push-button
W
for more than 3 seconds, until the
symbol
P01
sto
saved.
• Obviously, if yo
you should briefly press the push-button
W
as many times as
necessary to display the desired program.
P01
will be
displayed
PRESSING THE W PUSH-BUTTON BRIEFLY MAKES A
SELECTION, WHILE HOLDING IT DOWN FOR MORE
THAN 3 SECONDS SAVES THE DATA.
3.6.2. Save from a free program
T
proceeding as follows:
• Press the push-button
W
briefly and select the desired
program number.
• The symbol of free programs is flashing.
• Press the push b
procedure and mode (paragraph 3.1).
• Turn the knob
P
and set the welding current.
• If the TIG procedure has been sel
LED
O
(post gas) by means of the push-button
the desired value via the knob
P
(paragraph 3.1.)
• If you wish to adjust the "slope" times or other
parameters, after making these adjustments wh
necessary in order to weld,
follow the steps described
in paragraph 3.1.
• Weld, even briefly, and decide where to save
• To save in the p
button
W
for more than 3 seconds, until the numbe
flashing.
• To save in a different program, make your selection by
briefly pre
push button
W
for more than 3 seconds.
3.6.3 Save from a saved program
B
may edit the data in memory to upda
or to find new parameters to save in another program.
3.6.3.1 Update
• Alter turning on the machine,
be edited and edi
• Weld, even briefly.
• Hold down the
W
button
the save is confirme
flashing to steady).
3.6.3.2 Save in a n
• After turning on the machine,
be edited and edit them.
• Weld, even briefly.
• Briefly press the selecto
displayed.
• Hold down the
W
button until the save is confirmed
(program sy
4. REMOTE CONTROLS
The following remote contr
th
Item 570007 Foot control (used in TIG welding)
Item 535805 TIG UP/DOWN Torch.
Item ltem 570006 (used in MMA welding
Item 363307 Connection to simulta
torch and the pedal control.
Item 570007 may be used in any TIG welding mode with
this accessory.
Remote controls that include a potentiometer
regulate the we
maximum current set via the knob P
.
Remote controls with UP/DOWN Iogic regulate the
welding current from the minimum to
The remote control settings are always active in the
PL
program, while they are not active in a saved program.
Содержание TIG 1680
Страница 2: ...1 2 2...
