Elenco Electronics M-1006K, Сборка и инструкция по эксплуатации

Страница: 16 / 20

DIODE CHECK
RANGE RESOLUTION MAX TEST CURRENT MAX OPEN CIRCUIT VOLTAGE
DIODE 1mV 1.4mA 2.8V
TRANSISTOR h
FE
TEST
RANGE TEST RANGE TEST CURRENT TEST VOLTAGE
NPN/PNP 0 - 1000 Ib = 10
µ
A Vce 3V
-15-
SPECIFICATIONS
GENERAL
DISPLAY 3 1/2 digit LCD, with polarity
OVERRANGE INDICATION 3 least significant digits blanked.
MAXIMUM COMMON MODE
VOLTAGE
500V peak.
STORAGE ENVIRONMENT –15 O C to 50 O C.
TEMPERATURE COEFFICIENT (0 O C to 18 O C and 28 O C to 50 O C)
less than 0.1 x applicable accuracy
specification per
O C.
POWER 9V alkaline or carbon zinc battery.
DIMENSIONS 128 x 75 x 24mm.
DC VOLTAGE
RANGE RESOLUTION ACCURACY
200mV 0.1mV +0.5% rdg + 2d
2000mV 1mV +0.5% rdg + 2d
20V 10mV +0.5% rdg + 2d
200V 100mV +0.5% rdg + 2d
1000V 1V +0.5% rdg + 2d
MAXIMUM ALLOWABLE INPUT 1000VDC or peak AC.
INPUT IMPEDANCE 1M
Ω
.
DC CURRENT
RANGE RESOLUTION ACCURACY
200
µ
A 0.1
µ
A +1% rdg + 2d
2000
µ
A 1
µ
A +1% rdg + 2d
20mA 10
µ
A +1% rdg + 2d
200mA 100
µ
A +1.2% rdg + 2d
10A 10mA +2% rdg + 3d
OVERLOAD PROTECTION .25A/250V fuse (mA input only).
AC VOLTAGE
RANGE RESOLUTION ACCURACY
200V 100mV +1.2% rdg + 10d
750V 1V +1.2% rdg + 10d
MAXIMUM ALLOWABLE INPUT 750Vrms.
FREQUENCY 45 - 450Hz.
RESISTANCE
RANGE RESOLUTION ACCURACY
200
Ω
0.1
Ω
+0.8% rdg + 2d
2000
Ω
1
Ω
+0.8% rdg + 2d
20k
Ω
10
Ω
+0.8% rdg + 2d
200k
Ω
100
Ω
+0.8% rdg + 2d
2000k
Ω
1k
Ω
+1% rdg + 2d
MAXIMUM OPEN CIRCUIT VOLTAGE 2.8V.
RESISTANCE MEASUREMENT
Figure 7 shows a simplified diagram of the resistance measurement
function. A simple series circuit is formed by the voltage source, a
reference resistor from the voltage divider (selected by the selector
switches), and the test (unknown) resistor. The ratio of the two resistors
is equal to the ratio of their respective voltage drops. Therefore, since
the value of one resistor is known, the value of the second can be
determined by using the voltage drop across the known resistor as a
reference. This determination is made directly by the A/D converter.
Overall operation of the A/D converter during a resistance
measurement is basically as described earlier with one exception. The
reference voltage present during a voltage measurement is replaced by
the voltage drop across the reference resistor. This allows the voltage
across the unknown resistor to be read during the read period.
h
FE
MEASUREMENT
Figure 8 shows a simplified diagram of the h
FE
measurement function.
Internal circuits in the 7106 IC maintain the COMMON line at 2.8 volts
below V+. When a PNP transistor is plugged into the transistor socket,
base to emitter current flows through resistor R10. The voltage drop in
resistor R10 due to the collector current is fed to the 7106 and indicates
the h
FE
of the transistor. For an NPN transistor, the emitter current
through R11 indicates the h
FE
of the transistor.
Figure 7
Simplified Resistance Measurement Diagram
Ω
900k
Ω
Test
Resistor
100
Ω
900
Ω
2000
Ω
/Dio
200
Ω
7106
Reference
Voltage
Low Pass
Filter
Voltage
Source
Common
90k
Ω
9k
Ω
2000k
Ω
20k
Ω
200k
Ω
Figure 8
R10
220k
Ω
Common
R23
10
Ω
R11
220k
Ω
PNP NPN
7106
100mV
Ref.
Low Pass
Filter
V+
E C
C E
B B