background image

PARTS LIST

If you are a student, and any parts are missing or damaged, please see instructor or bookstore.
If you purchased this meter kit from a distributor, catalog, etc., please contact Elenco Electronics
(address/phone/e-mail is at the back of this manual) for additional assistance, if needed. DO NOT contact your
place of purchase as they will not be able to help you.

RESISTORS  

(Parts mounted on card.)

Qty.

Symbol

Value

Color Code

Part #

1

R9

.01

Shunt Wire

100161

1

R8

.99

.5% 1/4W

black-white-white-silver-green

109930

1

R7

9

.5% 1/4W

white-black-black-silver-green

119000

1

R13

100

5% 1/4W

brown-black-brown-gold

131000

1

R6

100

.5% 1/4W

brown-black-black-black-green

131050

1

R5

900

.5% 1/4W

white-black-black-black-green

139050

1

R17

910

1% 1/4W

white-brown-black-black-brown

139130

1

R12

1k

5% 1/2W

brown-black-brown-gold

141000

1

R14

4.7k

5% 1/4W

yellow-violet-red-gold

144700

1

R4

9k

.5% 1/4W

white-black-black-brown-green

149050

1

R15

30k

1% 1/4W

orange-black-black-red-brown

153030

1

R3

90k

.5% 1/4W

white-black-black-red-green

159050

1

R25

100k

5% 1/4W

brown-black-yellow-gold

161000

3

R10, R11, R24

220k

5% 1/4W

red-red-yellow-gold

162200

1

R2

352k

.5% 1/2W

orange-green-red-orange-green

163551

5

R18 - R22

470k

5% 1/4W

yellow-violet-yellow-gold

164700

1

R1

548k

.5% 1/2W

green-yellow-gray-orange-green

165451

1

R23

1M

5% 1/4W

brown-black-green-gold

171000

Placed in bag with carded parts.

1

R16

200

(201)

Potentiometer

191310

CAPACITORS

Qty.

Symbol

Value

Description

Part #

1

C1

100pF (101)

Disc

221017

4

C2, C3, C4, C6

.1

µ

F (104)

Mylar (small yellow)

251017S

1

C5

.1

µ

F (104) 

Mylar

251017

SEMICONDUCTORS

Qty.

Symbol

Value

Description

Part #

1

D1

1N4007

Diode (mounted on resistor card)

314007

MISCELLANEOUS

-1-

Qty.

Description

Part #

1

LCD

351115

2

Zebra

500006

1

PC Board IC Installed

516101

1

Fuse 0.2A, 250V

533002

1

Battery 9V

590009

1

Battery Snap

590098

1

Selector Knob

622104

1

Case Top (Black)

623113

1

Case Bottom (Black)

623209

1

Zebra Frame

629012

3

Screw 2mm x 6mm

643439

Qty.

Description

Part #

2

Screw 2mm x 10mm

643447

2

Fuse Holder Clips

663100

1

Socket Transistor

664007

3

Input Socket

664101

2

Ball Bearing

666400

6

Slide Contact

680013

2

Spring 1/4” (Selector Knob)

680014

1

Label Front

724012

1

Grease

790004

1

Solder Tube

9ST4

1

Test Lead Set

RWTL1000B

NOTE:

Not used but printed on PC board: R26 - R29, T1

The 7106 IC1 is already installed on the PC board. This type of installation is called C.O.B. (chip on
board). The IC is tested after it is installed on the PC board.

Содержание M-1006K





















Отзывы: