Electronics Diversified Lite Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 21

Electronics Diversified Lite Скачать руководство пользователя страница 17

Lite

17

PROTOCOL

ANALOG CONTROL PROTOCOL:

Analog Output: 0-10 Volts DC, 5 mA.
Connector: 25D chassis mount connector

Up to 24 channels of address are available in a 25D

connector.

(See 25D pin detail illustration)

Analog control requires a wire in the D25 connector and cable for

each dimmer addressed.

TO INSURE PROPER CONNECTION:

Physically inspect connectors prior to mating.
Connectors should mate easily. Do not force.
Always tighten locking screws on connector.

5XLR Output Pin Configuration

4

5

3

2

Lite consoles are available with two distinct types of dimmer

address protocols identified as:

DMX-512 PROTOCOL:

DMX-512 is based on USITT standards.
Connector: 5-pin XLR locking type

Keyed connector style
Up to 512 dimmer addressed on a single connection

All control pins are numbered. (See 5XLR pin detail illustration).
DMX-512 control is a digital signal transmitted over the control

cable.

TO INSURE PROPER CONNECTION:

Physically inspect connectors prior to mating.
Rotate connector to insure key alignment.
Connectors should mate easily. Do not force.

24-Channel Output Pin Configuration

SPECIFICATIONS

TECHNICAL

«
...
15
16
17
18
19
...
»

Содержание Lite






















Отзывы:

Нет отзывов