Electromotive TECgt Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 132

background image

TPS Failure Default Value (0-5V): 1.5 Volts

As can be seen, the

Fully Closed Throttle Voltage

setting is actually a bit above the actual closed

throttle voltage (1.1V > 1.0V). This is done because the Idle Speed Control will only start working when
the TPS reading is below the

Fully Closed Throttle Voltage

setting. The

Low Voltage Failure

setting is

made a few tenths of a volt lower than the actual closed throttle voltage (1.0V > 0.8V). This is done to
display code 22 for throttle position sensors that have either rotated in their mount or have failed
completely by outputting a lower-than-expected voltage. Likewise, the

High Voltage Failure

setting is

made a few tenths of a volt higher than the observed wide open throttle voltage. This will allow code 21 to
be displayed in the event of a high voltage failure. The

Failure Default Value

is the voltage that the

TECgt

will use for its TPS-based calculations when the TPS sensor has failed. Since this is a fixed value,

there will be no TPS-based acceleration enrichments when the TPS has failed. However, the Failure
Default Value is useful for applications using the TPS-MAP Blend feature because it defines a fixed
amount of TPS to blend with the MAP sensor during a TPS failure.

I.2.b. Wiring the Check Engine Light

The check engine light output gives a pull-to-ground for a light bulb. Terminal #2 on the

TECgt’s

gray connector is the pink wire for the check engine light. The circuit should not be allowed to flow more
than 0.25 Amps, which dictates that a light bulb of 3 Watts or less should be used. See

Figure I.2.1

for

wiring instructions.

Figure I.2.1:

Wiring diagram for the check engine output.

J. Data logging with the TECgt

There is a huge amount of data moving between the engine sensors and ECU when using the

TECgt

system. The data logging feature of the system allows users to view all of this data in graphical

format, thereby simplifying tuning and troubleshooting by a huge amount. Data logging is available in two
modes :

On-Board

Data logging (OBD) and

PC-Based

Data logging (PCD). As their name imply, OBD

stores sensor information inside the

TECgt’s

ECU, while PCD stores sensor information on the hard drive

of a laptop.

______________________________________________________________________________________
TECgt Manual Version 2.0

- Page 108 -

©2008 Electromotive, Inc.

«
...
106
107
108
109
110
...
»

Содержание TECgt





































































































































Отзывы:

Нет отзывов

Похожие инструкции для TECgt

Бренд: Harrington Страницы: 8

Бренд: OmarLift Страницы: 14

Бренд: Haier Страницы: 58

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Бренд: Eaton Страницы: 4

Бренд: Eaton Страницы: 10

Бренд: Eaton Страницы: 288

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Samson Страницы: 48

Бренд: WAGNER Страницы: 128

Бренд: Aeta Audio Systems Страницы: 24

Бренд: Reer Страницы: 2

Бренд: M-system Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды