6.17. Service function / disconnection pulse wash
General information
Calling above-mentioned service function
w
Calling the Service Functions is similar with all designs
Calling the function "Switch OFF Pulse Wash"
or key arrangements.
w
Always use the keys S1, S2, S3 and S4 independently
1.
Simultaneously press S2 and S4 and ...
from their program assignment depending on the model.
w
In service function mode, you can ALWAYS call the Pulse
2.
... switch on the appliance with ON/OFF switch S1.
Wash function by using keys S3 and S4. Use key S3 to
Keep keys S2 and S4 pressed simultaneously
modify the setting.
until the 3 acknowledging LEDs LD2, LD3 and LD4 are flashing.
(for abt. 4 seconds). Indicator LD1 at ON/OFF key lights up.
w
From works settings, Pulse Wash is always set to be active.
( Short-time illumination of LEDs is possible and does not constitute any fault)
3.
Simultaneously press S3 and S4 until the acknowledging LED
LD3 is flashing. LEDs LD2 and LD4 will go dark.
Indicator LD1 at ON/OFF key is lit.
The current status whether Pulse Wash is active or not
is indicated in the display. If there is no display available on the
model, the value is indicated by means of LED "End"
(also refer to Table left on this page)
w
If you deselect Pulse Wash the rot.speeds of the cir-
cul. pump are always increased to "High Pulse Speed".
Water consumption slightly increases. Extension
Switching the Pulse Wash Function on or off:
of time is possible depending on the temperature.
4. / 5.
Any further activation of function key S3 will
w
Table for the indication of on/off status:
switch the addition alternately on or off.
Abandoning the function
After the last activation of function key S3
you can leave the special program as follows:
After 60 seconds automatically all indications will go dark,
except for the LD1 of the ON/OFF key
or
Always applicable:
you switch the appliance off by means of ON/OFF key S1.
In order to call the totality of service functions always first
press the function keys S2 and S4 prior to switching the
Saving the status settings
appliance on by means of ON/OFF switch S1!
Immediately after each input of data, the currently valid status
Keep the keys pressed for abt. 4 seconds in order to
will be saved.
activate the function. This procedure is intentionally
distinguished from those for the customer functions.
ATTENTION:
In case of reduced key assemblies be sure
to observe Description Page B 1.
S1
On/Off
LD1
S2
LD2
LD3
S3
S4
LD4
S1
On/Off
LD1
S2
LD2
S3
LD3
S4
LD4
1.99
1.99
vertical key arrangement
horizontal key arrangement
display
"End"-LED
if no display available
depending on variant
1P
on
Pulse Wash is activ
0P
off
Pulse Wash is switched off
indication
comment
S1
On/Off
LD1
LD2
LD3
LD4
1.
2.
S1
On/Off
LD1
S2
LD2
LD3
S3
S4
LD4
LD1 is lit / LD2 - LD4 flashing
S4
S1
On/Off
LD1
S2
LD2
LD3
S3
1P
3.
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
S1
On/Off
LD1
S2
LD2
LD3
S3
LD4
S4
END
LD1 is lit / LD3 flashing
if no display
available:
... automatically Off after 60 sec.
... Off by actuating On/Off manually
0P
4.
END
1P
5.
END
S1
On/Off
LD1
S2
LD2
LD1 is lit / LD3 flashing
LD3
S3
S1
On/Off
LD1
S2
LD2
LD1 is lit / LD3 flashing
LD3
S3
S2
S3
LD4
S4
if no display
available:
if no display
available:
