manualshive.com logo in svg

Electrolux Diva EDW 2000, Руководство по обслуживанию

Поделиться
Скачать
Electrolux Diva EDW 2000 Скачать руководство пользователя страница 29

6.8. Input philosophy - interrupt program

l

Interrupt program

w

Using the ON/OFF key S1 you can interrupt the program as long as you want.
The same is valid for an interruption by opening the door.

w

There is no deleting function integrated in the ON/OFF key S1.

w

If the cycle is interrupted by using the ON/OFF key, all displays go out.

w

The cycle run will be continued by switching on again using the ON/OFF key S1 resp.
by closing the door, without that another key actuation becomes necessary.
Information: The cycle will be continued with a short time delay.

w

All displays and confirmations appear in the same condition as before the interruption.

l

What happens when opening and closing the door?

w

The appliance is switched on and is in the "prestart" mode

w

After opening the door all indications keep to be displayed on the panel. The power
supply of the electronic is fully guaranteed as long as the appliance remains
switched on.

w

The door is opened during the running cycle

w

After opening the door all indications keep to be displayed on the panel as long as
the appliance remains switched on using the ON/OFF key S1.

w

After closing the door the appliance will start automatically and the cycle run
will be continued.

Attention:

w

When the 1st regeneration has been reached in the program part "drying" the following is valid:

w

When the door is open longer than 30 seconds, the program will be deleted.
After closing the door, the appliance will be automatically again in the
"prestart" mode. A new program could be selected again immediately.

w

Switching off the appliance by pressing the ON/OFF key S1 also deletes the
current program from that moment.

(see description page B 3 / "Input philosophy program selection") 

l

What happens in case of resp. after a power failure?

w

In case of a power failure the appliance behaves as when switched off using the
ON/OFF key.
(see description above / under "Interrupt program")

w

After the mains have returned the appliance behaves as after being switched on using
the ON/OFF key S1.

w

After a power failure the cycle will continue without any necessary key actuations.

Содержание Diva EDW 2000















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды