Electrolux Diva EDW 2000, Руководство по обслуживанию

Страница: 37 / 46

6.14.2. Service function / readout of fault memory and single actuator selection:
General information Calling above-mentioned service function (appliances without display)
w
Calling the service functions is executed in all designs Calling the functions
resp. key arrangements analogously.
"readout of fault memory" and "single actuator selection"
w
For that you always have to use keys S1, S2, S3 and S4
1. Press keys S2 and S4 simultaneously and ...
indepedent of their variant-depending program load.
w
In the service function mode, key S2 is ALWAYS 2. ... and switch on the appliance by ON/OFF switch S1.
responsible for the functions "readout of fault memory" For that keep the keys S2 and S4 pressed simultaneously
and "single actuator selection".
until the 3 confirmation LEDs LD2, LD3 and LD4 are flashing.
(about 4 seconds). The LD1 display with ON/OFF key is lit.
( A temporary flashing up of LEDs is possible and no fault!)
3. / 4. By actuating the function key S2 you now can call the function.
The confirmation LED LD2 is flashing and the ON/OFF LED
continues flashing, LEDs LD3 and LD4 go out.
The first pressure on key S2 is indicated by the "END" LED.
By the second and third key pressure on S2 it is possible to
read out the second and third value of the fault memory.
(see description page B 19 / "Survey of fault displays")
w
A considerable difference regarding the output is From the 4. key pressure onward on key S2 the LED LD2 goes
represented by appliance variants with resp. without display. out and the LD3 starts flashing.
For this reason, this page describes the output for
Now you can call the single actuators one after the other.
appliances without display.
4. actuation: selection of regeneration valve
Page 14.1. describes the output for appliances with 5. actuation: selection of drain pump
display. 6. actuation: selection of the valve
(filling to level - if leavel already existing, no filling)
7. actuation: selection of heating
(only when level detected)
8. actuation: selection of circulation pump
9. actuation: selection of detergent dispenser
10.actuation: selection of drying fan
Always applicable: 11.actuation: selection of auto-dosing
In order to call the totality of service functions always first (is currently not used)
press the function keys S2 and S4 prior to switching the 12.actuation: selection of water hardness sensor
appliance on by means of ON/OFF switch S1!
(is currently not used)
Keep the keys pressed for abt. 4 seconds in order to
All positions can be called scrolling as many times as one wants.
activate the function. This procedure is intentionally
distinguished from those for the customer functions.
The various steps are switched onward manually. If the function key S2 is not pressed within 60 seconds, the service function
ATTENTION: In case of reduced key assemblies be sure is left automatically. All displays go out except the LD1 LED of the ON/OFF key. It is also possible to leave the function by
to observe Description Page B 1.
switching off the appliance using the ON/OFF key S1.
S1
On/Off
LD1
S2 LD2
LD3 S3
S4 LD4
S1
On/Off
LD1
S2
LD2
S3
LD3
S4
LD4
vertical key arrangement
horizontal key arrangement
END
END
S1
On/Off
LD1
LD2
LD3
LD4
1.
2.
S1
On/Off
LD1
S2
LD2
LD3 S3
S4 LD4
END
S1
On/Off
LD1
S2 LD2
LD3 S3
LD4
3.
S4
END
END
LD1 is lit / LD2 - LD4 flashing
LD1 is lit / LD2 flashing
S2
S3
S4
Indication 2. + 3. fault
Indication of single
actuators mode
S1
On/Off
LD1
S2 LD2
LD3 S3
LD4 S4
per key pressure
1 advancing
LD1 is lit, LD2 flashing
S1
On/Off
LD1
S2 LD2
LD3 S3
LD4 S4
per key pressure
1 advancing
LD1 is lit, LD3 flashing
END
S1
On/Off
LD1
LD2
LD3 S3
LD4
4.
S4
S2
LD1 is lit / LD2 flashing
S1
On/Off
LD1
S2 LD2
LD3 S3
LD4 S4
S1
On/Off
LD1
S2 LD2
LD3 S3
LD4 S4
... automatically Off after 60 sec
... Off by actuating On/Off manually