background image

 

 

207-SM Control Panel Instruction 12VDC and 24VDC For Swing Gates 
 

General safety rules 
WARNING: 

Unskilled  personnel  should  never  be  allowed  to  assemble,  repair  or  adjust  the  devices  and  all  necessary 

precautions  must  be  taken  to  prevent  accidents:  power  supply  disconnected  (including  backup  batteries  if  present).This 
product is not suitable for installation in explosive atmospheres.

 

 
 
Keep  this  handbook  carefully,  store  it  attached  to  the  technical  installation  leaflet  in  a  safe  place  where  it  is 
available to anyone who may need it and make sure that all involved personnel are aware of this. 

 

 

 

 

 

Type of product 
 

The 207 control panel has been designed to control 1 or 2 operators 12VDC and a 24VDC version for swing gates. It has an 
on-board integrated radio receiver. It is also possible to set the slowing down and anti-crushing features that grant an easy 
and  safe  installation,  free  from  interference  and  protected  against  atmospheric  and  electrostatic  discharges.  The  control 
board  207  has  succeeded  all  tests  concerning  the  electromagnetic  emissions  and  the  immunity  to  the  interference  as 
provided  by  the  European  rules  in  force.  It  conforms  to  the  directives  EMC  89/336/CEE,  92/31/CEE,  BT  73/23/CEE  and 
93/68/CEE 

 

 

 

Содержание 207-SM























Отзывы: