EKOM DK-50 2x2V/110, Инструкция по использованию, Руководство по обслуживанию

Страница: 39 / 108

INSTRUCTIONS FOR USE
11/2010 - 37 - NP-DK50 2V-5_04-2011_A
Handling
Fig.9 Unpacking
Compressor DK50 2V, DK50 2V/110, DK50 2x2V/110, DK50 2V/110/M, DK50 2x2V/110,
DK50 2x2V/110/M
(Fig.8,Fig.9)
After removing all packaging material, place the product on the floor and remove stabilization parts X and Y
(Detail A). Connect output hose with end-piece to the appliance. Plug the mains cord plug into a socket.
Place the drain hose into a container prepared in advance.
Compressor in box DK50 2VS (Fig.6, Fig.8)
After removing all packaging material, place the product on the floor and remove stabilization parts X and Y
(Detail A). Place the wall-mounted stopper (28) - 2 pcs onto the compressor housing in the rear top part of
the housing and put the housing onto a required place. The stoppers provide a sufficient distance of the
housing from a wall for thorough ventilation. For setting up the compressor in housing you must open the
door on the housing using the attached key and remove connecting reinforcement (27) in the front bottom
part of housing. If necessary, the door may be disassembled using door hinge (32). Connect the compressor
via distributions prepared in advance in a floor according to the installation plan or via holes in the rear part
of the housing (Fig.10). Protrude pressure hose via a hole in housing and connect it to the appliance in a
suitable way. Grasp the compressor at its handle and put it into the casing using built-in wheels (33). Fix the
hose (40) of a manometer (30) in a hose into the fast-on coupling on a compressor, put the connecting
reinforcement (27) back and connect the pressure hose to a compressor. Insert the electric power cord of a
compressor into a socket (34) on a housing. By slight rotation of rectification screws (44) set the correct
position of door against the casing frame. When closing the door the pin (45) on the door must easily snap in
the opening in the casing frame. Close the housing doors and duly lock the lock (26). Connect the mains
plug into the mains socket.
It is not allowed to leave the key in a lock! It must be saved against non-instructed persons!
Compressor in box DK50 2VS/M (Fig.6, Fig.8)
After removing all packaging material, place the product on the floor and remove stabilization parts X and Y
(Detail A). Place the compressor into housing similarly as in the previous paragraph. Prior to placing the
compressor into housing, protrude house for condensate drain via hole in housing and connect it to a bottle
(22).
Magnetic holder (31) with a vessel (22), for entrapping the condensate from the dryer may be fitted onto
any vertical part of casing, or from front on its door. When fixing the holder with a vessel at the housing side
it is necessary to consider a space of at least 11 cm between the housing and furniture. Distance smaller
than the specified one may cause problem with handling of the vessel.
Compressor in box DK50 2V/110S, DK50 2x2V/110S (Fig.7, Fig.9)
After removing all packaging material, place the product on the floor and remove stabilization parts X and Y
(Detail A). Place the wall-mounted stopper (28) - 2 pcs onto the compressor housing in the rear top part of
the housing and put the housing onto a required place. The stoppers provide a sufficient distance of the
housing from a wall for thorough ventilation. Dismount the door, fixed using 4 screws M5 (48) located in the
tapered edges of the door and disconnect earthing wire. If necessary, the top panel of the housing may be
opened by releasing the locks (47) by moderate rotation of screw driver according to pictogram and lifting
using a handrail (53). Gas springs (49) hold it in an open position. Insert the compressor into the housing so
that the compressed air outlet was oriented towards the operators and
so that a gap of at minimally 50