Edwards STP-301 Series Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 122

Edwards STP-301 Series Скачать руководство пользователя страница 52

STP-301/451 Series Instruction Manual

6-10

Installation

6.3

Attaching the STP Control Unit Front Panel to a Rack

The dimensions of the STP control unit front panel conform to EIA Standard.
Therefore, this panel can be attached to any type of commercially-available racks.
Attach the front panel unit to the rack according to the following steps:

•

Attach the front panel to a rack using the screw holes for the front panel.

•

Also support the STP control unit from the bottom using a support angle or a
similar tool.

•

To protect the STP control unit during transport, remove the rubber foot from
the bottom and attach the STP control unit to the rack using the screw holes for
the rubber foot.

◇

The STP control unit cannot be supported w ith only the screw s on the front
panel (the STP control unit is a heavy product).
Alw ays support it from the bottom.

◇

When installing the STP control unit, DO NOT block the ventilation port of the STP
control unit by the support angle or other things. It causes the control unit to
overheat.

◇

For the dimensions of the front panel and positions of screw holes for the rubber
foot, see Figure13.5, "External Appearance of the STP Control Unit."

Support Angle

Part: Secure with screw

Figure 6.6 Example of Securing the STP Control Unit

«
...
50
51
52
53
54
...
»

Содержание STP-301 Series



























































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды