manualshive.com logo in svg

Edge-Core ES3510MA-DC, Руководство по управлению, Страница: 705 / 1098

Поделиться
Скачать
Edge-Core ES3510MA-DC Скачать руководство пользователя страница 705

C

HAPTER

 26

  |  Access Control Lists

IPv6 ACLs

–  705  –

C

OMMAND

 M

ODE

Global Configuration

C

OMMAND

 U

SAGE

◆

When you create a new ACL or enter configuration mode for an existing 

ACL, use the 

permit

 or 

deny

 command to add new rules to the bottom 

of the list. To create an ACL, you must add at least one rule to the list.

◆

To remove a rule, use the 

no permit

 or 

no deny

 command followed by 

the exact text of a previously configured rule.

◆

An ACL can contain up to 64 rules.

E

XAMPLE

 

Console(config)#access-list ipv6 standard david

Console(config-std-ipv6-acl)#

R

ELATED

 C

OMMANDS

permit, deny (Standard IPv6 ACL) (705)

permit, deny (Extended IPv6 ACL) (706)

ipv6 access-group (708)

show ipv6 access-list (708)

permit

,

 deny

(Standard IPv6 ACL)

This command adds a rule to a Standard IPv6 ACL. The rule sets a filter 

condition for packets emanating from the specified source. Use the 

no

 

form to remove a rule.

S

YNTAX

{

permit

 | 

deny

} {

any

 

| 

host

source-ipv6-address 

| 

source-ipv6-address

[

/prefix-length

]} 

[

time-range

 

time-range-name

]

no

 {

permit

 | 

deny

} {

any

 

| 

host

source-ipv6-address 

| 

source-ipv6-address

[

/prefix-length

]}

any

 – Any source IP address.

host 

– Keyword followed by a specific IP address.

source-ipv6-address

 - An IPv6 source address or network class. The 

address must be formatted according to RFC 2373 “IPv6 Addressing 

Architecture,” using 8 colon-separated 16-bit hexadecimal values. 

One double colon may be used in the address to indicate the 

appropriate number of zeros required to fill the undefined fields.

prefix-length

 - A decimal value indicating how many contiguous bits 

(from the left) of the address comprise the prefix; i.e., the network 

portion of the address. (Range: 0-128)

time-range-name

 - Name of the time range. 

(Range: 1-30 characters)

Содержание ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов