Edge-Core ES3510MA-DC Скачать руководство пользователя страница 119

Страница: 119 / 1098

HAPTER

| Basic Management Tasks

Telnet Settings

– 119 –

ELNET

ETTINGS

Use the System > Telnet menu to configure parameters for accessing the

CLI over a Telnet connection. You can access the onboard configuration

program over the network using Telnet (i.e., a virtual terminal).

Management access via Telnet can be enabled/disabled and other

parameters set, including the TCP port number, time outs, and a password.

Note that the password is only configurable through the CLI.) These

parameters can be configured via the web or CLI interface.

CLI R

EFERENCES

◆

"Line" on page 535

◆

"Telnet Server" on page 621

ARAMETERS

The following parameters are displayed:

◆

Telnet Status

– Enables or disables Telnet access to the switch.

(Default: Enabled)

◆

TCP Port

– Sets the TCP port number for Telnet on the switch.

(Default: 23)

◆

Max Sessions

– Sets the maximum number of Telnet sessions that can

simultaneously connect to this system. (Range: 0-8)
A maximum of eight sessions can be concurrently opened for Telnet and

Secure Shell (i.e., both Telnet and SSH share a maximum number or

eight sessions).

◆

Login Timeout

– Sets the interval that the system waits for a user to

log into the CLI. If a login attempt is not detected within the timeout

interval, the connection is terminated for the session.

(Range: 0-300 seconds; Default: 300 seconds)

◆

Exec Timeout

– Sets the interval that the system waits until user input

is detected. If user input is not detected within the timeout interval, the

current session is terminated. (Range: 0-65535 seconds; Default: 600

seconds)

◆

Password Threshold

– Sets the password intrusion threshold, which

limits the number of failed logon attempts. When the logon attempt

threshold is reached, the system interface becomes silent for a

specified amount of time (set by the Silent Time parameter) before

allowing the next logon attempt. (Range: 0-120; Default: 3 attempts)

◆

Quiet Period

– Sets the amount of time the management interface is

inaccessible after the number of unsuccessful logon attempts has been

exceeded. (Range: 0-65535 seconds; Default: Disabled)

OTE

Password checking can be enabled or disabled for login to the

console connection (see

"login" on page 537

). You can select

Содержание ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ES3510MA-DC

Отзывы:

Edge-Core ES3510MA-DC, Руководство по управлению, Страница: 119 / 1098

Результаты поиска

Содержание ES3510MA-DC

Отзывы: