manualshive.com logo in svg

Edge-Core ES3510MA-DC, Руководство по управлению, Страница: 417 / 1098

Поделиться
Скачать
Edge-Core ES3510MA-DC Скачать руководство пользователя страница 417

C

HAPTER

 15

  |  Basic Administration Protocols

Switch Clustering

–  417  –

◆

A switch can only be a member of one cluster.

◆

After the Commander and Members have been configured, any switch 

in the cluster can be managed from the web agent by choosing the 

desired Member ID from the Show Member page. 

C

ONFIGURING

G

ENERAL

 S

ETTINGS

FOR

 C

LUSTERS

Use the Administration > Cluster (Configure Global) page to create a 

switch cluster. 

CLI R

EFERENCES

◆

"Switch Clustering" on page 563

C

OMMAND

 U

SAGE

First be sure that clustering is enabled on the switch (the default is 

disabled), then set the switch as a Cluster Commander. Set a Cluster IP 

Pool that does not conflict with the network IP subnet. Cluster IP addresses 

are assigned to switches when they become Members and are used for 

communication between Member switches and the Commander.

P

ARAMETERS

These parameters are displayed:

◆

Cluster Status

 – Enables or disables clustering on the switch. 

(Default: Disabled)

◆

Commander Status

 – Enables or disables the switch as a cluster 

Commander. (Default: Disabled)

◆

IP Pool

 – An “internal” IP address pool that is used to assign IP 

addresses to Member switches in the cluster. Internal cluster IP 

addresses are in the form 10.x.x.member-ID. Only the base IP address 

of the pool needs to be set since Member IDs can only be between 1 

and 36. Note that you cannot change the cluster IP pool when the 

switch is currently in Commander mode. Commander mode must first 

be disabled. (Default: 10.254.254.1)

◆

Role

 – Indicates the current role of the switch in the cluster; either 

Commander, Member, or Candidate. (Default: Candidate)

◆

Number of Members

 – The current number of Member switches in the 

cluster.

◆

Number of Candidates

 – The current number of Candidate switches 

discovered in the network that are available to become Members.

W

EB

 I

NTERFACE

To configure a switch cluster:

1.

Click Administration, Cluster.

2.

Select Configure Global from the Step list.

Содержание ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов