manualshive.com logo in svg

Edge-Core ES3510MA-DC, Руководство по управлению, Страница: 1037 / 1098

Поделиться
Скачать
Edge-Core ES3510MA-DC Скачать руководство пользователя страница 1037

C

HAPTER

 44

  |  IP Interface Commands

IPv6 Interface

–  1037  –

ipv6 address

This command configures an IPv6 global unicast address and enables IPv6 

on an interface. Use the 

no

 form without any arguments to remove all IPv6 

addresses from the interface, or use the 

no

 form with a specific IPv6 

address to remove that address from the interface.

S

YNTAX

 

[

no

]

 ipv6 address

 

ipv6-address

/

prefix-length

ipv6-address

 - A full IPv6 address including the network prefix and 

host address bits.

prefix-length

 - A decimal value indicating how many contiguous bits 

(from the left) of the address comprise the prefix (i.e., the network 

portion of the address). 

D

EFAULT

 S

ETTING

 

No IPv6 addresses are defined

C

OMMAND

 M

ODE

 

Interface Configuration (VLAN)

C

OMMAND

 U

SAGE

 

◆

All IPv6 addresses must be according to RFC 2373 “IPv6 Addressing 

Architecture,” using 8 colon-separated 16-bit hexadecimal values. One 

double colon may be used in the address to indicate the appropriate 

number of zeros required to fill the undefined fields.

◆

To connect to a larger network with multiple subnets, you must 

configure a global unicast address. This address can be manually 

configured with this command, or it can be automatically configured 

using the ip 

ipv6 address autoconfig

 command.

◆

If a link-local address has not yet been assigned to this interface, this 

command will assign the specified static global unicast address and also 

dynamically generate a link-local unicast address for the interface. (The 

link-local address is made with an address prefix of FE80 and a host 

portion based the switch’s MAC address in modified EUI-64 format.)

◆

If a duplicate address is detected, a warning message is sent to the 

console.

E

XAMPLE

 

This example specifies a full IPv6 address and prefix length.

Console(config)#interface vlan 1

Console(config-if)#ipv6 address 2001:DB8:2222:7272::72/96

Console(config-if)#end

Console#show ipv6 interface

Vlan 1 is up

IPv6 is enable.

Link-local address:

  FE80::2E0:CFF:FE00:FD/64

Global unicast address(es):

  2001:DB8:2222:7272::72/96, subnet is 2001:DB8:2222:7272::/96

Содержание ES3510MA-DC











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов