background image

 

 

Versatrax 50™ In-Line 

 

Document: UMBU014988.docm  

Revision: A04 

Created by: KJW 

Date: 20 Nov 2019 

IPN: 3080215-A04 

Source Location: C:\ePDM\ISLEng\products\bu-vt50vehicles\manuals\UMBU014988.docm

 

 

Page 18 of 25 

 

User Ma

nual

 

  Ensure camera and light ports are clean.  

  Check the reel for the following: 

  Check that the Shipping Brake is disengaged, and the Friction Brake is engaged.  

  Check that the tether has no loose, dangling coils.  Dangling coils can propagate as the drum rotates 

and have the potential to jump the drum.  Take care of these before deploying the tether.   

  Power up the system and check the following: 

  Check for sufficient SSD drive space for recording.   

  Check record directories are set. 

  Test video recording. 

  Test track control. 

  Test camera control. 

 

Post-Operations Check 

A Post-Ops inspection should be carried out after every deployment using the following checklist:  

  Inspect the tether for damage as it is reeled in.   

  Visually inspect vehicle for entrained debris or mechanical damage.   

  Test each function to ensure proper operation. 

  Clean the system by  hosing  it down  with  water at regular  line  pressure.  Do  not  pressure  wash.   The 

tracks may be cleaned off by hosing them down while running.  If the system has been used in salt water, 
thoroughly rinse the vehicle with fresh water right away.   

  Take time to pack the system properly for transport away from the worksite.   

  Store the system in a dry environment. 

 

Note:

   

Ensuring  the  Versatrax  50™  system  is  always  stored  in  good  working  condition  will  minimize 

deployment time for future inspections. 

 

 

 

 

Содержание Inuktun Versatrax 50 In-Line


























Отзывы: