ECR 075 97gb страница 32 Скачать руководство пользователя

Страница: 32 / 80

8 - ELECTRICAL CONNECTIONS

•

Outdoor Sensor, if used.

A. Provided with boiler in accessory kit.

B. Locate outdoor sensor to protect against wind and

direct sunlight. Mounting instructions provided with

sensor.

C. Maximum wire length is 100 ft (30m) for 22 ga.

wire, or 150 ft (45m) for 18 ga. wire.

D. Connect wires to low voltage terminal plug

OUTDOOR SENSOR terminals. Wires are

interchangeable.

•

System Sensor (Multiple boiler applications only)

•

Domestic Hot Water (DHW) Thermostat, if used.

A. Use temperature control with dry contacts rated

at 0.5 amps @ 120 VAC. Boiler control does not

provide power to DHW temperature control.

NOTICE

Do not apply power to DHW T-T terminals. Dry

contact only, use of isolation relay may be necessary.

B. Maximum wire length is 330 ft (100 m) 22 gauge

wire.

C. Connect wires (interchangeable) to low voltage

terminal plug DHW T-T terminals. Wires are

interchangeable.

•

Central Heating Thermostat

A. Use thermostat or boiler system control with dry

contacts related 0.5 amps @ 120 VAC.

Boiler

control does not provide 24 VAC power to central

heating thermostat.

B. Locate and install thermostat per manufacturer's

instructions. Maximum wire length is

330 ft (100

m) for 22 ga. wire.

C. Connect wires to low voltage terminal plug CH T-T

terminals. Wires are interchangeable.

NOTICE

Use dry contact for wires to CH T-T terminal and

DHW T-T terminal. E33 error code is displayed if

voltage is sent back to the control board. If error

is not corrected for extended period of time, this

voltage can permanently damage control board.

Содержание 075 97gb

















































































Результаты поиска

Содержание 075 97gb

Отзывы:

Похожие инструкции для 075 97gb

Бренды по названию

Популярные бренды

ECR 075 97gb, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 075 97gb

Отзывы:

Похожие инструкции для 075 97gb

Бренды по названию

Популярные бренды