ECR 075 97gb страница 36 Скачать руководство пользователя

Страница: 36 / 80

Verify Burner, Proper Operation

Inspect burner flame through Sight Glass. See

figure 9-5.

Operate boiler through several heating cycles,

including domestic hot water, if used. Verify proper

operation.

Reset control parameters to operating settings if

adjusted to allow startup and operation test.

Follow instructions TO TURN OFF GAS TO APPLIANCE

if boiler is not being placed into immediate operation.

Enter installer information on Warranty Registration

Card.

Gather all instructions, manuals, wiring diagrams,

warranty registration card and other supporting

information. Review with user and/or affix in

conspicuous location adjacent to boiler.

Gas

Min.

Max.

Natural Gas

9.0

9.5

<200ppm

Propane

10.0

11.0

<200ppm

NOTICE

Contact Technical Support @ 800-325-5479 for

additional information or assistance.

Natural Gas only**

Measure input. Compare to table above. Continue

to measure input and CO

until both measured

values are within range specified in tables

Propane Gas

Most propane systems do not have flow meters.

Check CO

. Propane should be between 10% and

11.0%.

•

If CO

is low increase gas flow following figure

9-3 & 9-4.

•

If CO

is high decrease gas flow following figure 9-3

& 9-4.

9 - START UP PROCEDURE

FIGURE 9-3 Gas Valve - Models 075/100 MBH

1/4" Flat Head

Screwdriver

• To increase gas flow turn 'throttle' left or counter

clockwise

• To decrease gas flow turn 'throttle' right or

clockwise .

•

Limit adjustment to one turn and retest.

Содержание 075 97gb

















































































Результаты поиска

Содержание 075 97gb

Отзывы:

Похожие инструкции для 075 97gb

Бренды по названию

Популярные бренды

ECR 075 97gb, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 075 97gb

Отзывы:

Похожие инструкции для 075 97gb

Бренды по названию

Популярные бренды