ECR 075 97gb страница 13 Скачать руководство пользователя

Страница: 13 / 80

5.1

General

•

Install piping in accordance with authority having jurisdiction.

NOTICE

Use two (2) wrenches when tightening and fitting

to pipe boiler's threaded fittings. Boiler's internal

piping can be damaged if subjected to excessive

torque.

•

Support system piping and safety relief valve discharge

piping. Boiler's internal piping and wall mount bracket can

be damaged if subjected to excessive weight.

•

Size central heating pump (and domestic hot water pump,

if used) for system requirements only. Heat exchanger

pump compensates for pressure drop through boiler

internal piping and heat exchanger.

• Thoroughly clean and flush system before connecting to

boiler.

•

If oil is present in system water, use approved detergent to

wash system.

•

Flush system to remove any solid objects such as metal

chips, fibers, or Teflon tape, etc.

5.2

Special Conditions

•

System piping exposed to freezing conditions: Use

inhibited proplyene glycol solutions certified by fluid

manufacturer for use with closed water heating system.

Do not use automotive or ethylene glycol.

•

Boiler installed above radiation level (or as required by

authority having jurisdiction). Integral low water cutoff

provided in boiler. See pages 7 & 9.

•

Boiler used in connection with refrigeration system.

Install piping in parallel with boiler, with appropriate

valves to prevent chilled medium from entering boiler.

•

System piping connected to heating coils located in air

handling unit exposed to refrigerated air circulation. Install

flow control valves or other automatic means to prevent

gravity circulation of boiler water during cooling cycle.

5.3

Safety Relief Valve and Air Vent

NOTICE

Boiler rated at 150 psig (1.03 MPa) maximum

allowable working pressure. Boiler provided with

30 psig (206 kPa) safety relief valve. Field source

safety relief valve for system pressures greater than

25 psig. Temperature Pressure Gauge satisfactory

for 60 psig operation. Field source temperature

pressure gauge for system pressures greater than

60 psig.

• Install safety relief valve and air vent using pipe fittings

provided with boiler. See figure 5-1

•

Install safety relief valve with spindle in vertical position.

•

Do not install shutoff valve between boiler and safety

relief valve.

WARNING

•

Poison hazard. Ethylene glycol is toxic. Do not

use ethylene glycol.

•

Never use automotive or standard glycol antifreeze,

even ethylene glycol made for hydronic systems.

•

Ethylene glycol can attack gaskets and seals used

in hydronic systems.

•

Use only inhibited proplyene glycol solutions

certified by fluid manufacturer as acceptable for

use with closed water heating system.

• Thoroughly clean and flush any system that used

glycol before installing new Boiler.

•

Provide user with Material Safety Data Sheet

(MSDS) on fluid used.

5 - HYDRONIC PIPING

NOTICE

Do not expose boiler and condensate piping to

freezing temperatures.

FIGURE 5-1 Safety Relief Valve & Air Vent

3/4" NPT

Close Nipple

3/4"F x 3/4"M

NPT Tee

3/4" x 1/4" NPT

90° Elbow

Air Vent

3/4 NPT

Safety Relief

Valve

3/4" NPT

90° Elbow

Содержание 075 97gb

















































































Результаты поиска

Содержание 075 97gb

Отзывы:

Похожие инструкции для 075 97gb

Бренды по названию

Популярные бренды

ECR 075 97gb, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 075 97gb

Отзывы:

Похожие инструкции для 075 97gb

Бренды по названию

Популярные бренды