ECR International Dunkirk Helix DKVLT-050 Скачать руководство пользователя

Страница: 53 / 84

13 - TROUBLE SHOOTING

Error shows when safet

y circuit is

open. R

emo

ve J13 connector from

control module. Check for continuit

between two pins connected to two pink wires, is continuit

y a

vailable?

YES

Replace Control Module

Boiler fired without enough w

ater flow

through heat ex

changer

. Heat ex

changer

is o

ver heated. Either high limit or heat

changer temper

ature switch is open.

Check the following:

•

Air in system?

•

Verify water flow in system piping

•

Flush system if water is dirty.

Is boiler supply pipe (abo

heat ex

changer) hot?

ait for boiler to cool down.

YES

Replace Brok

en S

witch

Unplug molex connector on supply temper

ature sensor

. Check continuit

between two pins on sensor (two pins

connected

two

pink

wires)

Is continuit

y a

vailable?

YES

Check for loose connections on two pink wires on J13 connector

, supply sensor

, and

safet

y temper

ature switch.

YES

Fix Loose Connections

Replace Wire Harness

Let all z

ones

run until w

ater

temper

ature

drops.

Is Heat Ex

changer surface hot?

YES

Check high limit

and surface temper

ature

switches

P/N# 240008888, Rev. O [07/15/2015]

Содержание Dunkirk Helix DKVLT-050





















































































Результаты поиска

Содержание Dunkirk Helix DKVLT-050

Отзывы:

Похожие инструкции для Dunkirk Helix DKVLT-050

Бренды по названию

Популярные бренды

ECR International Dunkirk Helix DKVLT-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Dunkirk Helix DKVLT-050

Отзывы:

Похожие инструкции для Dunkirk Helix DKVLT-050

Бренды по названию

Популярные бренды