ECM NH3 5250 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 62

ECM NH3 5250 Скачать руководство пользователя страница 51

47

Appendix G: Setting Up ATI Vision for ECM Modules

NOTE:

While shown here for a single LambdaCAN* module, the same procedure applies for any of

ECM’s CAN-based devices (i.e. Analyzers or Modules) as well as for multiple device simultaneously
connected on the same bus.

Introduction

Connecting ECM LambdaCAN hardware to ATI VISION software is simple and does not require any
third-party software interface. Using the ECM Configuration Tool software to produce a .dbc database
file, and the ATI VISION CANMonitor interface, any available hardware CAN interface can be used to
read LambdaCAN data.

Hardware Setup

A typical hardware configuration is shown in Figure 1. In this example, a Kvaser Leaf Light CAN-USB
adapter is used. Other supported adapters have a similar procedure. Connect the DB9 CAN connector
of the LambdaCAN to the PC to CAN adapter. Supply 11-28V DC (5A min. supply) to the
LambdaCAN. For the case of an ECM analyzer (ex. Lambda 5220), connect to CAN port on display
head. Do not directly connector to modules.

Figure 1: Equipment Schematic Layout

PC to CAN

Adapter

Termination
Resistor

DB9 Connector

CAN

Software



ATI VISION 3.6.2



ECM Configuration Tool v4.13

PC with

ATI VISION

and ECM

Configuration

Tool

USB

Kvaser Leaf Light

LambdaCAN

DC Power Supply

11-28V

«
...
49
50
51
52
53
...
»

Содержание NH3 5250































































Отзывы:

Нет отзывов