manualshive.com logo in svg

ECM NH3 5250, Инструкция по эксплуатации, Страница: 24 / 62

Поделиться
Скачать
ECM NH3 5250 Скачать руководство пользователя страница 24

 

20 

CONF (Configure) Setup Option 

 

CONF setup appears at the end of the setup list for the lower channel.  To enter CONF, press 

the  SYS  key  until  “MOd”  appears  on  the  upper  display,  press  the 

  key  until  “CONF” 

appears on the bottom display, and then press the ENT key.  CONF relates to display head 

(as opposed to lambda module or sensor) setup.  

 

 

LEdS 

 

The  display  intensity  is  programmable.    Press  the  ENT  key  when  “LEdS”  appears  on  the 

lower  display,  press  the 

  or 

  keys  until  the display intensity is  suitable, press  ENT, and 

press SYS to return to RUN mode. 

 

 

1V4V 

 

This  feature  commands  a  1  V  (when  “1V”  is  on  lower  display)  or  4  V  (when  “4V”  is  on 

lower display) output on all six analog outputs.  This feature is useful when troubleshooting 

the interface with an external data acquisition device. 

 

 

CAN 

 

Figure 1 shows cabling connected to the back of the display head for CAN communication.  

Depending on where the display head appears in your CAN bus, the termination resistor may 

have to be present or removed. 

 

The CAN data communicated is: 

 

1.

 

What is being sent to analog output 1 

2.

 

What is being sent to analog output 2 

3.

 

What is being sent to analog output 3 

4.

 

What is being sent to analog output 4 

5.

 

What is being sent to analog output 5 

6.

 

What is being sent to analog output 6 

7.

 

What is being sent to the upper display (but not averaged by display) 

8.

 

What is being sent to the lower display (but not averaged by display) 

9.

 

An error code for the upper channel.  See 

Appendix C

. 

10.

 

An error code for the lower channel.  See 

Appendix C

. 

11.

 

An auxiliary code for the upper channel. 

12.

 

An auxiliary code for the lower channel. 

 

It is important to note that if a parameter that is being displayed is changed (by pressing the 

 

or 

 key), the CAN data will be changed also to that newly displayed parameter for 7 or 8 

(above).  Similarly for an analog output.  LOCKing the display head can be used to avoid this 

problem. 

 

 

 

 

 

 

 

 

Содержание NH3 5250































































Отзывы:

Нет отзывов