ECM NH3 5250 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 62

ECM NH3 5250 Скачать руководство пользователя страница 30

26

Appendix A: 5200 Series Instruments Parts List

01 Display Heads (Just display head. Must add cables, etc.)

01-01 NOx 5210 (just head, no module, no cable, no sensor)
01-02 Lambda 5220 (just head, no module, no cable, no sensor)
01-03 EGR 5230 (just head, no module, no cable, no sensor)
01-04 dashCAN (includes cable and T)
01-05 (big box, 6 analog outputs)
01-06 dashCANc
01-07 NOx/NH3 5240 (just head)
01-08 dashCAN2 (blue box, 2 analog outputs, includes cable and T)
01-09 NOx/NH3 5241 (just head)
01-10 NH3 5250 (just head)

02 CAN Modules (just module)

02-01 LambdaCAN (just module, no sensor, no cables)
02-02 NOxCAN (for original sensor, just module, no sensor, no cables)
02-03 NOxCAN-G (for "G" sensor just module, no sensor, no cables)
02-04 LambdaCANc (just module, no sensor, no cables)
02-05 appsCAN (just module, no cables)
02-06 baroCAN (just module, no sensors, no cables)
02-07 NOxCAN-T (for "T" sensor, just module, no sensor, no cables)
02-08 LambdaCANp (just module, no sensor, no cables)
02-09 LambdaCANd (just module, no sensor, no cables)
02-10 gpCAN (just module, no cables)
02-11 COCO2CAN (just module, no sensor, no cables)
02-12 NH3CAN (just module, no sensor, no cables)

03 Simulators, Heater

03-01 LambdaCAN Sensor Simulator (just module, no cable)
03-02 NOx Sensor Simulator (just module, no cable)
03-03 Ceramic Sensor Heater (just module, no cable)
03-04 NOxg Sensor Simulator (just module, no cable)
03-05 NOxt Sensor Simulator (just module, no cable)
03-06 LambdaCANp Sensor Simulator (just module, no cable)

04 Power Supplies

04-01 AC/DC Power Supply, Universal, 24V
04-02 Vboost Supply, 10~14VDC to 24VDC @ 14.5A
04-03 30A AC/DC Power Supply, 15V, 100~240VAC
04-04 15A AC/DC Power Supply, 15V, 120VAC
04-05 60A AC/DC Power Supply, PWR 60, 15V, 120VAC

«
...
28
29
30
31
32
...
»

Содержание NH3 5250































































Отзывы:

Нет отзывов