Echo TYPE1-E CSG-670 Скачать руководство пользователя

Страница: 24 / 24

CSG-670 TYPE1-E

730 mm × 250 mm × 360 mm (28.7 in. × 9.8 in. × 14.2 in.)

10.8 kg (23.8 lb.) dry mass w/o cutting wheel

Air-cooled, 2-stroke, single cylinder gasoline engine
66.8 mL (4.069 cu. in.)
50.0 mm (1.969 in.)
34.0 mm (1.339 in.)
7.3 : 1
Piston valve
WALBRO diaphragm type with speed limiter
Flywheel magneto, capacitor discharge ignition type
NGK BPM6Y
Spark arrestor muffler

Throttle trigger with throttle lockout and throttle latch

650 mL (22.9 US. fl. oz.)

Mixed fuel
50 : 1 ratio with ECHO Power Blend X™, ISO-L-EGD (ISO/CD 13738) and

JASO M345-FC/FD two-stroke, air-cooled engine oil.

Use 89 octane unleaded.
Do not use fuel containing methyl alcohol, more than 10 % ethyl alcohol or

15 % MTBE.

Do not use alternative fuels such as E-20 or E-85.

Automatic rewind starter

Clutch Centrifugal type

Idle:

2700 r/min

Clutch engagement: 3800 r/min
Wide open throttle: 9500 to 10500 r/min

BANDO ORC 850
2 : 1
Spring
305 mm × 20 mm dia. (12.0 in. × 25/32 in. dia.)
305 mm × 25.4 mm dia. with adapter (12.0 in. × 1.0 in. dia.)

Rubber isolaters mounted between the engine and the handles

3 stage type: sponge filter, bellows type paper filter and nylon mesh filter

Option
Option

Dimensions

Length × Width × Height

Mass

Engine

Displacement
Bore
Stroke
Compression ratio
Intake
Carburetor
Ignition system
Spark plug
Muffler

Throttle control

Fuel tank capacity

Fuel

Fuel oil ratio

Gasoline

Starter system

Clutch

Engine speed

Cutting device

Belt
Pulley ratio
tensioner
Cutting wheel

Vibration reduction system

Air cleaner

Attachment

Water kit
Cart kit

STORAGE AFTER USE

SPECIFICATIONS

•

Inspect and adjust every part of the cut-off saw.
- Completely clean every part and repair if

necessary.

- Apply thin coating of oil on metal parts to

prevent rust.

•

Remove cutting wheel.

•

Drain fuel tank, pull starter slowly a few times to
drain fuel from carburetor.

•

Pour a small amount of clean motor oil into spark
plug hole, pull starter and crank the engine until
piston reaches: TOP DEAD CENTER.

•

Store in a dry area, free from dust.

WARNING

Do not store in enclosure where fuel fumes
may accumlate or reach an open flame or
spark.

CAUTION

Do not lend or rent your cut-off saw without
the operator’s manual.

* Technical data subject to change without notice.

NOTE

For future reference, you should keep this
operator’s manual.

If this operator’s manual has become illegible
or is lost, please purchase a new one from
your ECHO dealer.

Содержание TYPE1-E CSG-670

























Результаты поиска

Содержание TYPE1-E CSG-670

Отзывы:

Похожие инструкции для TYPE1-E CSG-670

Бренды по названию

Популярные бренды

Echo TYPE1-E CSG-670, Руководство оператора

Результаты поиска

Содержание TYPE1-E CSG-670

Отзывы:

Похожие инструкции для TYPE1-E CSG-670

Бренды по названию

Популярные бренды