manualshive.com logo in svg

Echo TYPE1-E CSG-670, Руководство оператора

Поделиться
Скачать
Echo TYPE1-E CSG-670 Скачать руководство пользователя страница 22

22

CSG-670 TYPE1-E

5. Accelerate to full throttle for 2 - 3 seconds to

clear any excess fuel in the engine, then return
to idle.
Accelerate engine to full throttle to check for
smooth transition from idle to high speed.
If engine hesitates turn “L” needle CCW 1/8 turn
and repeat acceleration.
Continue adjustment until smooth acceleration
results.

6. Check idle speed and reset if necessary as

described in item 4. If a tachometer is available
idle speed should be set to 2600 - 2800 r/min.

   WARNING

Cutting attachment must not move when unit
is idling.

   CAUTION

When starting, idling adjustment speed
should be adjusted not to rotate the wheel.
Correct idle speed is adjusted 2600 to 2800
r/min. Or 1/4 turn CCW from the point the
wheel stops moving.
When you experience trouble with the
carburetor, contact your dealer.

Every unit is run at the factory and the carburetor is
set in compliance with Emission Regulations. In
addition, the carburetor is equipped with “H”  (High
Speed) and “L” (Low Speed) needle adjustment
limiters that prevent settings outside acceptable
limits.

1. Before adjusting carburetor clean or replace air

filter and muffler “Spark Arrestor Screen”.

2. Start engine and run several minutes to bring to

operating temperature. Flash choke twice during
warm-up to clear any air from the fuel system.

3. Stop engine.

Turn “H” speed needle counterclockwise (CCW)
to stop.
Turn “L” speed needle midway between full
clockwise (CW) stop and CCW stop.

4. Idle Speed Adjustment:

•

Start engine, turn “Idle” speed adjustment

knob CW until the wheel begins to turn, then
turn knob out CCW until the wheel stops
turning.
Turn knob out, CCW, an additional 1/4 turn.

CARBURETOR ADJUSTMENT

Idle Speed
Adjustment Knob

H:High Speed Needle

L: Low Speed Needle

Содержание TYPE1-E CSG-670

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды