Echo SRM-266T Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 40

background image

SRM-266T

EMISSION CONTROL (EXHAUST / EVAPORATIVE)

© 10/2014 ECHO Inc.

X7502027204

9

Avoid Hot Surfaces

• Keep exhaust area clear of flammable debris. Avoid contact

during and immediately after operation.

Equipment

Use only ECHO attachments. Serious injury may result from the use of a non-approved attachment
combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or
accessories which have not been tested and approved by ECHO. Read and comply with all safety
instructions listed in this manual and safety manual.

• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.

• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is

damaged or missing.

• Check that the cutting attachment is firmly attached and in safe operating condition.

• Check that handle and harness (if included) are adjusted for safe, comfortable operation. See Assembly

Section for proper adjustment.

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings.

◆

ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.

◆

DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

◆

NEVER reach into any opening while the engine is running. Moving parts may not be visible through
openings.

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or
leaks are found, do not use unit, otherwise serious personal injury or property damage may occur.
Have unit repaired by an authorized servicing dealer before using.

EMISSION CONTROL (EXHAUST / EVAPORATIVE)

EPA 2010 and Later

The emission control system for the engine is EM (engine modification)
and, if the second to last character of the Engine Family on the Emission
Control Information label (sample below) is “C”, “K”, or “T”, the emission
control system is EM and TWC (3-way catalyst). The fuel tank/fuel line
emission control system is EVAP (evaporative emissions). Evaporative
emissions for California models are only applicable to fuel tanks

«
...
7
8
9
10
11
...
»

Содержание SRM-266T









































Отзывы:

Нет отзывов

Похожие инструкции для SRM-266T

Бренд: XU1 Страницы: 6

Бренд: Parkside Страницы: 128

Бренд: Tanaka Страницы: 2

Бренд: Stanley Страницы: 18

Бренд: Vitek Страницы: 28

Бренд: Zero88 Страницы: 4

Бренд: Nakayama Страницы: 12

Бренд: FLORABEST Страницы: 42

Бренд: Certa Страницы: 8

Бренд: Meec tools Страницы: 37

Бренд: McCulloch Страницы: 60

Бренд: Kobalt Страницы: 18

Бренд: Haussmann Страницы: 24

Бренд: Haussmann Страницы: 24

Бренд: Haussmann Страницы: 39

Бренд: Haussmann Страницы: 20

Бренд: Haussmann Страницы: 35

Бренд: McCulloch Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды