Echo SRM-266T Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

background image

SRM-266T

STORAGE

© 10/2014 ECHO Inc.

X7502027204

31

STORAGE

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep
exhaust area clear of flammable debris during transportation or when storing, otherwise serious
property damage or personal injury may result.

Long Term Storage (Over 30 Days)

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective
storage maintenance which includes the following:

1. Store unit in a dry, dust free place, out of the reach of children.

Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.

2. Place the stop switch in the “OFF” position.

3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.

4. Perform all periodic lubrication and services that are required.

5. Tighten all the screws and nuts.

6. Drain fuel tank completely. Press purge bulb 6-7 times to remove remaining fuel from carburetor then

drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.

7.

a. Allow engine to cool then remove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke

engine oil into the cylinder through the spark plug hole.

b. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.

c. Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston

reaches the top of its travel and leave it there.

8. Install the spark plug (do not connect ignition cable).

«
...
29
30
31
32
33
...
»

Содержание SRM-266T









































Отзывы:

Нет отзывов

Похожие инструкции для SRM-266T

Бренд: Makita Страницы: 100

Бренд: Gardena Страницы: 15

Бренд: Troy-Bilt Страницы: 40

Бренд: Echo Страницы: 24

Бренд: Ryobi Страницы: 26

Бренд: Dolmar Страницы: 36

Бренд: Work Pro Страницы: 4

Бренд: Work Pro Страницы: 6

START-LINE ACD-200

Бренд: Trust Страницы: 52

Бренд: Kobalt Страницы: 18

Auger Torque T150

Бренд: KINSHOFER Страницы: 32

PLT3043A, RY70101A

Бренд: Ryobi Страницы: 18

Бренд: Jonsered Страницы: 36

Бренд: Jonsered Страницы: 65

TrimMac 251 SST

Бренд: McCulloch Страницы: 11

Бренд: King Canada Страницы: 3

Бренд: Bergman Страницы: 9

Бренд: K-JAPAN Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды