Echo SRM-266T Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 40

Echo SRM-266T Скачать руководство пользователя страница 16

16

X7502027204

© 10/2014 ECHO Inc.

OPERATION

SRM-266T

Operation With Blades

Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield, barrier
bar or U-handle, and harness can result in serious personal injury. Follow installation instructions.

DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS.

• Arbor Diameter of Upper Blade Plate must match arbor diameter of blades.

• New cotter pin required each time blade is installed.

• Brush cutters over 7.5 kg (16.5 lbs.) dry weight (weight w/o fuel) require a double shoulder harness.

Note: The Barrier Bar is used to restrict rearward movement of the unit. The Barrier Bar is NOT A HANDLE

and should not be gripped when using or carrying the unit.

Blade Selection

The type of Blade used MUST be matched to the type and size of material cut. An improper or dull
blade can cause serious personal injury. Blades MUST be sharp. Dull blades increase the chance of
kick-out and injury to yourself and bystanders.

Plastic/Nylon Grass/Weed Blades

may be used where ever

the nylon line head is used. DO NOT use this blade for heavy
weeds or brush!

TO USE

THESE

BLADES

Pro Maxi-Cut

Grass/Weed

Blade

Rigid Plastic

Tri-Cut

Grass/Weed Blade

Metal Blade

You

must

install

these

parts!

Support Handle, w/or

w/o Barrier Bar

U-Handle or Support

Handle

w/Barrier Bar

U-Handle or Support

Handle

w/Barrier Bar

Plastic Shield

Plastic Shield

Metal Shield

Harness

Harness

Harness

Upper Plate &

Flat Washer

Upper Plate

& Glide Cup

Upper/Lower

Blade Plates

Hex Nut

Hex Nut

Hex Nut

New Cotter Pin

New Cotter Pin

New Cotter Pin

«
...
14
15
16
17
18
...
»

Содержание SRM-266T









































Отзывы:

Нет отзывов