Echo SRM-266T Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

background image

22

X7502027204

© 10/2014 ECHO Inc.

MAINTENANCE

SRM-266T

MAINTENANCE

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and
hot surfaces.

Your ECHO unit is designed to provide many hours of trouble free service. Regular scheduled maintenance
will help your unit achieve that goal. If you are unsure or are not equipped with the necessary tools, you may
want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is
not listed, see your ECHO Dealer for repairs.

Skill Levels

Level 1

= Easy to do. Common tools may be required.

Level 2

= Moderate difficulty. Some specialized tools may be required.

ECHO offers

REPOWER

TM

Maintenance Kits and Parts to make your maintenance job easier.

Maintenance Intervals

MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN
IMPORTANT NOTE

- Time intervals shown are maximum. Actual use and your experience will determine the

frequency of required maintenance.

MAINTENANCE PROCEDURE NOTES:

(1) Apply lithium based grease every 25 hours of use.

(2) Apply lithium based grease every 50 hours of use.

* Replacement is recommended based on the finding of damage or wear during inspection.

COMPONENT/SYSTEM

MAINTENANCE

PROCEDURE

REQ’D

SKILL

LEVEL

DAILY

OR

BEFORE

USE

EVERY

REFUEL

3

MONTHS

YEARLY

Air Filter

Inspect/Clean

1

I / C *

R *

Choke Shutter

Inspect/Clean

1

I / C

Fuel Filter

Inspect/Replace

1

I *

I / R *

Fuel Cap Gasket

Inspect/Replace

1

I *

R *

Fuel System

Inspect/Replace

1

I *

I *

Spark Plug

Inspect/Clean

1

I / C / R *

Cooling System

Inspect/Clean

2

I / C

Muffler Spark Arrestor

Inspect/Clean/Replace

2

I / C / R *

Cylinder Exhaust Port

Inspect/Clean/Decarbon

2

I / C

Drive Shaft
(Flex Cable Models)

Grease

2

I (1)

Gear Housing

Grease

2

I (2)

Recoil Starter Rope Inspect/Clean

1

I / C *

Screws/Nuts/Bolts Inspect/Tighten/Replace

1

I *

«
...
20
21
22
23
24
...
»

Содержание SRM-266T









































Отзывы:

Нет отзывов

Похожие инструкции для SRM-266T

Бренд: Shindaiwa Страницы: 164

Бренд: Weed Eater Страницы: 7

Бренд: Pope Страницы: 12

Power Xchange PXCGTS-018

Бренд: Ozito Страницы: 10

Бренд: Echo Страницы: 26

Бренд: Zenoah Страницы: 100

4rtists BOOST+ FX7870GBPE

Бренд: BaBylissPro Страницы: 124

Бренд: Mi-Heat Heizsysteme Страницы: 4

Бренд: INSTEON Страницы: 16

Бренд: Wahl Страницы: 12

Бренд: Texas Equipment Страницы: 20

Tanaka TCG 22EAB

Бренд: Hitachi Koki Страницы: 68

Бренд: Hitachi Koki Страницы: 88

Бренд: Hitachi Koki Страницы: 128

Бренд: IBEA Страницы: 48

Бренд: IBEA Страницы: 76

Бренд: Meec tools Страницы: 37

Бренд: Meec tools Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды