background image

4

5 INCH CHIPPER/SHREDDER/BLOWER

SAFETY

1.6 SAFETY DECALS

Contact with rotating driveline can cause 

death. Do not operate without all driveline, 

tractor and equipment shields in place. Ensure the driveline is securely 

attached at both ends and driveline shields that turn freely on the 

driveline are in place.

Read and understand this owner/operators 

manual. Be completely familiar with the 

controls and the proper use of this equipment
Obtain and wear safety glasses and 

use hearing protection at all times when 

operating this machine.
Before inspecting or servicing any part of this 

machine, shut off power source, disconnect 

spark plug wire from spark plug and make 

sure all moving parts have come to a 

complete stop.

See Section 1.7 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine 

and the associated hazards. See the engine owner’s manual or contact the engine manufacturer for engine safety 

instructions and decals.

Keep hands and feet out of inlet and discharge 

openings while machine is operating to avoid serious 

personal injury. Stop and allow machine to come to a 

complete stop before clearing obstructions.

3

1

2

PN 12168

PN 12169

PN 12172

Do not insert branches larger than 3/4" 

into shredder or machine damage may 

occur.

7

PN 12176

Keep hands and feet out of inlet and 

discharge openings while machine is 

operating  to  avoid  serious  personal  injury. 

Stop and allow machine to come to a complete stop before clearing 

obstructions.

Read and understand your owners manual before operating. If owners 

manual was not included or you have any questions, please call 

800.247.7335 or 701.282.5520 (U.S.A.).

Check blade bolts for proper torque after 

every 8 hours of operation. Check blades 

and rotate or resharpen daily or as required to keep blades sharp. 

Refer to owners manual for instructions. Failure to do so may cause 

poor performance, damage or personal injury and will void the machine 

warranty.

9

6

8

PN 12175

PN 12250

PN 14942-00

Do not operate this equipment in the vicinity 

of bystanders. Do not allow children to 

operate this equipment. Always stand clear 

of discharge area when operating this machine. Keep face and body 

away from discharge areas.

4

PN 12173

Do not operate this equipment in the 

vicinity of bystanders. Do not allow 

children to operate this equipment. 

Always stand clear of discharge area 

when operating this machine. Keep 

face and body away from discharge 

areas. Rotate the discharge tube over the hitch before towing and lock 

securely in place.

10

PN 32109-00

Do not operate machine without shields in place. Failure 

to do so may cause serious injury or death.

5

PN 12174

PN 12174

Содержание Bear Cat SC5540B





























Отзывы: