ECA CONFEO PREMIX P 14 HM Скачать руководство пользователя страница 3

Страница: 3 / 84

INTRODUCTION

First of all, we would like to thank you for choosing E.C.A brand. E.C.A.

Confeo

Premix condensing boilers have

been designed to meet for an efficient, safe and comfortable central heating and hot water requirement. The

Confeo

Premix condensing boilers can possibly use natural gas or LPG according to the desired fuel preference.

There is no standard LPG models. LPG usage is only possible after gas conversion in the field.

HM Model (Boiler)
HCH Model (Heat Only)

Both Central Heating (CH) and Domestic Hot Water (DHW).

Only for Central Heating (CH).

HST Model (System Boiler)

Both for Central Heating (CH) and Domestic Hot Water (DHW) with external

storage tank (not included).

The assembly and usage information of

14/20/

/28

/30/35 kW

Confeo

Premix condensing boilers are

available in this manual. Detailed information have been provided in the guide regarding the technical

specification of the boiler, selection of the boiler location, fitting its water, gas, flue and electric supply

connections, gas conversion, maintenance information and solving of possible failures. Please carefully read

the manual in order to benefit from all the features of your boiler.

The Benchmark Checklist and Service Record Card are located at the back of the Operating Manual.

The Benchmark Checklist must be filled by gas safe engineer during installation.
Operating Manual and Service Manual must be handed over the user for future operations.

Service Record Card must be filled by gas safe engineer and handed over the user after
each service operation and annual Maintenance.

1.1

Installer’s Responsibility

The installer is responsible for the installation and initial start-up

of the boiler. Instructions are given below.



Check Operating and Service manuals and follow instructions before installation.



Carry out installation in compliance with the prevailing legislation and standarts.



Be sure that the system is flushed and inhibitor added.



Only gas safe engineer must operate the boiler.



Explain the user about installation and operation of boiler.



Fill the Comissioning Checklist.



Give all Operating and Service manuals to user.



The warranty certificate must be registered by gas safe engineer within 30 days after installation.

Содержание CONFEO PREMIX P 14 HM





















































































Результаты поиска

Содержание CONFEO PREMIX P 14 HM

Отзывы:

Похожие инструкции для CONFEO PREMIX P 14 HM

Бренды по названию

Популярные бренды

ECA CONFEO PREMIX P 14 HM, Руководство по обслуживанию

Результаты поиска

Содержание CONFEO PREMIX P 14 HM

Отзывы:

Похожие инструкции для CONFEO PREMIX P 14 HM

Бренды по названию

Популярные бренды