Eaton SystemStak DGM-5-30 Series Скачать руководство пользователя страница 7

Страница: 7 / 42

EATON

DGM**-5 30 Design E-VLST-BB002-E April 2015

N-7

Basic Characteristics

Maximum flow

120 l/min (32 USgpm)

Pilot flow@ 50

C (120

F) and 315 bar (4500 psi)

400–700 ml/min (24 in

/min-43 in

/min)

Maximum operating pressure

315 bar (4500 psi)ar (450 psi)

Pressure overshoot

31 bar (450 psi)

Operating temperature

-0

to 80

C (32

to 180

Weights

DGMC 2,9 kg (6.5 lbs) DGMC2 3,6 kg (7.9 lbs)

Response time: For conditions of 5 liters (300 in

) of oil under compression and a flow rate of 120 l/min (32 USgpm) typical response is:

Initial pressure

Final pressure

Response time

17 bar (250 psi)

35 bar (500 psi)

95 ms

35 bar (500 psi)

140 bar (2000 psi)

110 ms

35 bar (500 psi)

315 bar (4500 psi)

150 ms

Operating Data

Performance Data

DGMC-5 and DGMC2-5 Insertion Loss

Insertion Loss

Total change in pressure drop from through ports “P” “B”,

“A” and “T”caused by the addition of the SystemStak valve

to a hydraulic circuit. Insertion loss curves (see top left):
1. DGMC2-5-AT-**-(E)-BT-**-(E)-(RC)*-30

DGMC-5-AT-**-(E)-(RC)*-30

DGMC-5-BT-**-(E)(RC)-*-30

2. DGMC-5-PT-**-(E)-(RC)*-30
3. DGMC2-5-AB-**-BA-**-30

DGMC-5 and DGMC2-5 Vented Pressure (RC models only)

(Not applicable for crossport models)

DGMC-5 and DGMC2-5 Pressure Override

The pressure override chart (below) shows typical override of

different adjustment ranges at maximum settings.

The vented pressure chart (above) indicates flow from control

port to discharge port over relief element.

Pressure Drop bar

Pressure Drop ps

200

150

100

Flow l/min

Flow USgpm

100

120

Pressure bar

Pressure psi

250

200

150

100

Flow l/min

Flow USgpm

100

120

Pressure psi

Pressure bar

Pressure psi

200

150

100

4000

3000

2000

Flow l/min

Flow USgpm

100

120

1000

300

350

250

5000

Override at minimum (“P”) setting all models

Содержание SystemStak DGM-5-30 Series











































Результаты поиска

Содержание SystemStak DGM-5-30 Series

Отзывы:

Бренды по названию

Популярные бренды

Eaton SystemStak DGM-5-30 Series, Руководство пользователя

Результаты поиска

Содержание SystemStak DGM-5-30 Series

Отзывы:

Бренды по названию

Популярные бренды