Eaton SystemStak DGM-5-30 Series Скачать руководство пользователя страница 10

Страница: 10 / 42

EATON

DGM**-5 30 Design E-VLST-BB002-E April 2015

N-10

DGMC2-5-AT-**-BT-**-30
Dual Relief

mm (inches)

See page 37 for optional adjustment devices.

See page 38 for interface dimensions.

• Back pressure in drain is added to this

setting for internal drain models only.

* Remote control port. Both ends

(“ RC” models only)

(1.97)

(1.18)

(1.89)

“W” models

(max. ext.)

typ. both ends

ISO 4401-AC-05-4-A (NFPA D05)

Mounting surface

13,5

(0.53)

153,9 (6.06)

(1.97)

11,7

(0.46)

33,2

(1.31)

71,6

(2.82)

max.

Adjust pressure “B” port. Adjust

clockwise to increase pressure setting.

Wrench size both ends

33,2

(1.31)

69,5

(2.74)

15,3

(0.60)

both

ends

11,5

(0.45)

both

ends

both

ends

12,5 (0.49)

both ends

Hex key

External drain port *

(both ends).

Plugged for internal drain.
Adjust pressure “A” port. Adjust

clockwise to increase pressure

setting.

13 (1/2”)

4 (5/32”)

4 mounting holes

6,9 (0.27) through

9,50 (0.37) counterbore

36,5 (1.44) deep

for bolt extenders

(order separately)

BKE-6M-50M (M6 metric) or

BKE-4-50M (.2500-20 UNC).

Torque: 11,3-14,7 Nm

(100-130 lb. in.)

* Remote control port. Both ends

(“ RC” models only)

* External connection port thread type:
“S” models - SAE-4 O-ring boss port

(0.4375-20 UNF-2B thread).

“B” models - G 1/8 (1/8 BSPF) 15 in model code

Installation Dimensions

Содержание SystemStak DGM-5-30 Series











































Результаты поиска

Содержание SystemStak DGM-5-30 Series

Отзывы:

Бренды по названию

Популярные бренды

Eaton SystemStak DGM-5-30 Series, Руководство пользователя

Результаты поиска

Содержание SystemStak DGM-5-30 Series

Отзывы:

Бренды по названию

Популярные бренды