manualshive.com logo in svg

Eaton SystemStak DGM-5-30 Series, Руководство пользователя

Поделиться
Скачать
Eaton SystemStak DGM-5-30 Series Скачать руководство пользователя страница 21

EATON  

DGM**-5 30 Design  E-VLST-BB002-E  April 2015

N-21

N

Operating Data

Performance Data

DGMR Performance Curves 
Insertion Losses

These curves show the typical pressure drop for each flow 

path in the valve for fluid viscosity range 21-32 cSt 

(100-150 SSU).
The total insertion loss for the valve is calculated by summing 

the losses through each of the four flow paths.

1.  “P” port for all models. 

“A” port of DGMR-5-B*-30 

“B” port of DGMR-5-A*-30

2.  “T” port for all models.
3.  Free flow through service port of counterbalance.
4.  Piloted port open through service port of counterbalance.

Pressure Drop ba

r

Pressure Drop psid

30

20

300

0

0

Flow l/min

Flow USgpm

20

40

60

80

100

120

5

10

15

20

25

30

10

150

60

40

450

600

750

50

4

3

Pressure Drop psid

4

0

Flow l/min

Flow USgpm

40

80

10

20

2

20

1

30

120

2

40

20

60

100

0

3

1

10

30

50

Pressure Drop bar

5

1 5

2 5

Basic Characteristics

Maximum flow 

120 l/min (32 USgpm)

Load holding leakage @70% of pressure setting 

0.35 ml/min.

Cracking Pressure Adjustment Range 

60-210 bar (900-3000 psi)

Pilot Ratios 

4:1, 10:1

Maximum operating pressure 

315 bar (4500 psi)

Leakage flow rate @ 50° C (120° F) and 315 bar (4500 psi) 

5 drops/min, Port A to Port A

1

 at 70% of crack setting

Operating temperature 

-40° to 80°C (-40° to 180°F)

Weights 

4,5 kg (10 lbs)

Содержание SystemStak DGM-5-30 Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды