Eaton RTX-12510 Скачать руководство пользователя страница 81

Страница: 81 / 126

. .

Timing and Installation of the Auxiliary Countershaft Assemblies

1. On the small diameter low range gear of each counter-

shaft, mark the tooth which is stamped with an "O".

2. Place one of the countershaft into position in the rear

plate, meshing the marked tooth on the countershaft
between two of the marked teeth on the low speed gear.

Use a soft bar to start the rear bearing on to the shaft

and into the case bore and use a bearing driver to com-
plete the installation. Check the synchronizer assembly
during bearing installation to make sure that the springs
do not pop out. Repeat the procedure for the remaining
countershaft.

NOTE: Make sure that the bearing inner race is installed

on the front of each auxiliary countershaft.

3. Install the snap ring on the rear of each countershaft.

4. Install the countershaft rear bearing covers.

Содержание RTX-12510































































































































Результаты поиска

Содержание RTX-12510

Отзывы:

Похожие инструкции для RTX-12510

Бренды по названию

Популярные бренды

Eaton RTX-12510, Руководство по обслуживанию

Результаты поиска

Содержание RTX-12510

Отзывы:

Похожие инструкции для RTX-12510

Бренды по названию

Популярные бренды