Eaton RTX-12510 Скачать руководство пользователя страница 22

Страница: 22 / 126

6. Low Range, Check Point D

With the gearshift lever in neutral, pull the control but-
ton up and disconnect the low range air line at shift
cylinder.

a. Repeat procedure under Check Point C, reversing the

position of the control button in order to check the

low range operation.

7. Range Shift Cylinder – Check Point E

If any of the seals in the range shift cylinder are de-
fective the range shift will be affected. The degree of lost

air, of course, will govern the degree of failure, from
slow shift to complete failure to shift.

Refer to Illustration F for location of seals. Make sure

cylinder bore is clean to prevent damage to piston seal.
Use only a very light amount of shellac or Permatex on

cover gasket to prevent clogging cylinder. Tighten cover
capscrews securely.

Содержание RTX-12510































































































































Результаты поиска

Содержание RTX-12510

Отзывы:

Похожие инструкции для RTX-12510

Бренды по названию

Популярные бренды

Eaton RTX-12510, Руководство по обслуживанию

Результаты поиска

Содержание RTX-12510

Отзывы:

Похожие инструкции для RTX-12510

Бренды по названию

Популярные бренды