Eaton RTX-12510 Скачать руководство пользователя страница 122

Страница: 122 / 126

Reassembly of the Air System

1. Install the adapter plat on the front case. Use the align-

ment sleeve to make sure that the bore in the adapter
plate lines up properly with the bore in the front case.

3. Check to make sure that the piston in the air valve is

either all the way forward or all the way to the rear and
install the alignment sleeve in the bore.

Install the air valve on the adapter plate, tightening the

four capscrews evenly.

5. If previously removed, install the brass fittings in the air

valve and range shift cylinder. Secure the filter/regulator
assembly and the air valve.

Connect the 1/4" ID supply air line between the filter/

regulator assembly and the air valve.

122

2. Install the actuating pin and spring in the bore.

Reassembly-Air System

Содержание RTX-12510































































































































Результаты поиска

Содержание RTX-12510

Отзывы:

Похожие инструкции для RTX-12510

Бренды по названию

Популярные бренды

Eaton RTX-12510, Руководство по обслуживанию

Результаты поиска

Содержание RTX-12510

Отзывы:

Похожие инструкции для RTX-12510

Бренды по названию

Популярные бренды