Eaton PowerXL DX-NET-ETHERCAT-2 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 56

background image

2 Engineering

2.1 EtherCAT

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

13

2 Engineering

2.1 EtherCAT

EtherCAT (Ethernet for Control Automation Technology) is an industrial
Ethernet system that uses standard frames and the physical layers defined in
the IEEE 802.3 series of Ethernet standards. It was developed by Beckhoff
Automation GmbH.

EtherCAT is normally used for applications in which I/O data and parameters
need to be transmitted quickly.

In EtherCAT systems, the master is the only node in a segment that is
allowed to actively send EtherCAT frames. All other nodes simply forward
the frames. The last node in the segment will detect an open port and send
the frame back to the master.

The DX-NET-ETHERCAT-2 EtherCAT module works as a slave within the
EtherCAT network to which it is connected. The module contains the entire
EtherCAT protocol stack, including the CANopen-over-EtherCAT application
functions defined in DS301. By using EtherCAT, a bus topology containing
several hundred nodes can be implemented. In fact, the network‘s size is vir-
tually unlimited.

«
...
15
16
17
18
19
...
»

Содержание PowerXL DX-NET-ETHERCAT-2

























































Отзывы:

Нет отзывов

Похожие инструкции для PowerXL DX-NET-ETHERCAT-2

Бренд: Warpia Страницы: 28

Бренд: 3idee Страницы: 7

Бренд: MillSO Страницы: 2

Бренд: Proyecson Страницы: 148

Бренд: Atheros Страницы: 48

Бренд: SWEEX Страницы: 8

Бренд: l-com Страницы: 34

Бренд: Keyspan Страницы: 40

Бренд: Pioneer Страницы: 17

Бренд: Planet Страницы: 69

Бренд: CHIEF Страницы: 4

Home MWD 50003 CE

Бренд: Somogyi Страницы: 8

Vanson SMP-90WAT

Бренд: Clas Ohlson Страницы: 5

Бренд: Clas Ohlson Страницы: 5

Бренд: Clas Ohlson Страницы: 5

Бренд: Clas Ohlson Страницы: 16

Бренд: APLIC Страницы: 24

Бренд: Uconnect Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды