Eaton PowerXL DX-NET-ETHERCAT-2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 56

background image

1 Device series

1.7 Maintenance and inspection

12

DX-NET-ETHERCAT-2

01/14 MN040009EN

www.eaton.com

1.7 Maintenance and inspection

The DX-NET-ETHERCAT-2 fieldbus connection will not require any mainte-
nance if the general rated operational data (

Page 9), as well as all Ether-

CAT-specific technical data, is adhered to. However, external factors can
influence the components’s lifespan and function. We therefore recommend
that the devices are checked regularly and the following maintenance mea-
sures are carried out at the specified intervals.

Table 2:

Recommended maintenance

The DX-NET-ETHERCAT-2 fieldbus connection has not been designed in
such a way as to make it possible to replace or repair it. If the card is damaged
by external influences, repair is not possible.

1.8 Storage

If the fieldbus connection is stored before use, suitable ambient conditions
must be ensured at the site of storage:

•

Storage temperature: -40 - +85 °C,

•

Relative average air humidity: < 95 %, no condensation permitted.

1.9 Service and warranty

Contact your local sales partner if you have a problem with your Eaton
fieldbus connection.
When you call, have following data ready:

•

the exact part no. (= DX-NET-ETHERCAT-2),

•

the date of purchase,

•

a detailed description of the problem which has occurred with the
DX-NET-ETHERCAT-2 fieldbus connection.

Information concerning the guarantee can be found in the Terms and
Conditions Eaton Industries GmbH.

24-hour hotline: +49 (0) 180 5 223 822

e-mail:

[email protected]

1.10 Disposal

The DX-NET-ETHERCAT-2 fieldbus connection can be disposed of as electri-
cal waste in accordance with the currently applicable national regulations.
Dispose of the device according to the applicable environmental laws and
provisions for the disposal of electrical or electronic devices.

Maintenance measures

Maintenance interval

Check the filter in the control panel doors
(see the manufacturer‘s specifications)

6 - 24 months (depending on the environment)

Check the tightening torques of the control signal terminals

regularly

Check connection terminals and all metallic surfaces for
corrosion

6 - 24 months (depending on the environment)

«
...
14
15
16
17
18
...
»

Содержание PowerXL DX-NET-ETHERCAT-2

























































Отзывы:

Нет отзывов

Похожие инструкции для PowerXL DX-NET-ETHERCAT-2

Бренд: StarTech.com Страницы: 2

Бренд: Targus Страницы: 2

TL-WN951N - IEEE 802.11b/g 802.11n Draft 2.0 PCI Wireless Adapter

Бренд: TP-Link Страницы: 41

Бренд: GodEngine Страницы: 92

CardPark APA-4510

Бренд: Adaptec Страницы: 8

Бренд: Lanpro Страницы: 16

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 26

Vaio PCG-21513L

Бренд: Sony Страницы: 24

Бренд: Sony Страницы: 104

Бренд: VoIP Solutions Страницы: 35

Бренд: Adaptec Страницы: 12

78165 SAS/SATA RAID

Бренд: Adaptec Страницы: 2

Бренд: Adaptec Страницы: 106

Бренд: Adaptec Страницы: 110

Бренд: Adaptec Страницы: 66

Бренд: Adaptec Страницы: 152

Бренд: Arduino Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды