Eaton DPCT Скачать руководство пользователя страница 28

Страница: 28 / 64

Programming

DPCT IOM InsTruCTIOn OPeraTIOn Manual

MN124018EN January 2023 www.eaton.com

onto a USB storage device. The statistics can be cleared by

pressing the “Clear All Controller Statistics” button. Please

refer to Table

for the statistical values that are recorded.

Table 5.

DPCT Controller Statistics

statistics

Total Powered Time

Total Engine Run Time

Last Engine Run Time

Calls to Start

Engine Starts

Minimum AC Voltage

Maximum AC Voltage

Minimum Battery #1 Voltage

Minimum Battery #2 Voltage

Maximum Battery #1 Voltage

Maximum Battery #2 Voltage

Minimum Battery #1 Amperage

Minimum Battery #2 Amperage

Maximum Battery #1 Amperage

Maximum Battery #2 Amperage

Minimum System Pressure

Maximum System Pressure

Last System Startup

Last Engine Start

Last Engine Test

Last Overspeed

Last Low Oil Pressure

Last High Engine Temperature

Last ECM In Alternate

Last Fuel Injection Malfunction

Last ECM Warning

Last ECM Failure

Last High Raw Water Temperature

Last Low Raw Water Temperature

Last Low Engine Temperature

Last Fail to Start

Last Low Fuel

Last High Fuel

Last Fuel Spill

Last Charger #1 Failure

Last Charger #2 Failure

Last Battery #1 Failure

Last Battery #2 Failure

Last Starter Coil #1 Failure

Last Starter Coil #2 Failure

Last AC Power Failure Alarm

Last DC Failure

5.10.3 Controller diagnostics

The DPCT controller will display a number of diagnostic

values that can be viewed on the user interface touch

screen or saved onto a USB storage device.
The main diagnostic page will display the firmware version,

supply voltages, and transducer information.
The input status page will display the state of each input

contact. Pressing the input buttons, the controller will

override the state of that input for one minute. If the button

is depressed a second time, the input will resume normal

operation. If the screen is exited, the input will resume

normal operation.
The output status page will display the state of each output

relay on the I/O board, solenoid valve, and alarm. Pressing

the output buttons, the controller will override the state

of that output for one minute. If the button is depressed a

second time, the output will resume normal operation. If the

screen is exited, the output will resume normal operation.

The audible alarm can be silenced for a period of ten (10)

minutes that will not reset by leaving the screen.
The controller is equipped with on-board communication

diagnostics. The last page in the Controller Diagnostic menu

allows the user to test the transfer and receive functions of

the display board. The screen will provide a prompt that the

test successfully passed or failed.

5.10.4 Start up information

This screen will display all events that were logged while in

the START UP tab.

5.10.5 Save to USB

Data can be saved to an external USB memory device via

the USB port located on the controller door. When a valid

USB device is inserted, the button text will change from

“INSERT USB” to “PRESS TO SAVE”. Once the data has

been saved to the USB, the display will prompt the user to

remove the USB device.
Message history, statistics, diagnostics, configuration,

and the start up file will be saved onto the USB in comma

separated value (CSV) format.

Содержание DPCT

































































Результаты поиска

Содержание DPCT

Отзывы:

Похожие инструкции для DPCT

Бренды по названию

Популярные бренды

Eaton DPCT, Инструкция по эксплуатации

Результаты поиска

Содержание DPCT

Отзывы:

Похожие инструкции для DPCT

Бренды по названию

Популярные бренды