background image

8

EATON CORPORATION Cutler-Hammer

 Pow-R-Command 750 LCD Display  Instruction Leaflet IL01412018E  Effective: February 2009

C. Control Table

a. Switch List

Lists the switches that have already, or will be configured for 
association with a group.

1. Type

Allows the user to select one of the various switch types 
listed below contained within the submenu.

a. Choose Switch Type

i.   Maintained Normally Open

 Maintained switch with a normally open contact.

ii.   Maintained Normally Close

Maintained switch with a normally closed contact.

iii.  Maintained CH

 Maintained change switch.

iv. Momentary ON/OFF

Momentary ON/OFF switch.

v.

Momentary ON

Momentary ON switch.

vi. Momentary OFF

 Momentary OFF switch.

vii. None

2. Group

a. Choose Group

Allows the user to associate the control of a group with 
a certain specified input.

3. Switch

Permits the user to specify which input is associated with 
the switch.

4. Description

5. Name

6. Enabled By

Allows the user to enable to the switch via a group or flag.

a. Choose Group/Flag

i.   None

ii.   Group List

Shows a list of groups to enable the switch.

7. Time Delay

8. Override

a. On

b. Off

c. Restore

9. Communication Loss

a. Stay

Stay in the present state last recorded before loss of 
communication with the master unit.

b. On

Stay in the ON state when loss of communication with 
the master unit occurs.

c. Off

Stay in the OFF state when loss of communication with 
the master unit occurs.

D. System

a. Description Field

The description field allows the user to assign a 20-character 
description describing the respective breaker.

b. Name Field

The name field allows the user to modify the default 
4-character load identifier used with the respective breaker.

c. Address Field

Each unit can have a unique address numbered from 1 to 120 
for networking purposes. This field allows the user to assign 
an address to the unit.

d. Bypass ON

Bypasses ALL loads ON.

e. Bypass ON

Bypasses ALL loads OFF.

f. Clear Bypass

Clears the bypassed or overridden status of the loads and 
returns them to normal operation and control.

g. Restart

Restarts the unit.

h. Date/Time

1. Change Date

Allows the user to change the date.

2. Change Time

Allows the user to change the time.

3. Daylight Savings Time

Allows the user to enable or disable daylight 
savings time.

4. Astronomical Location

Allows the user to change latitude and longitude for 
calculations for sunrise and sunset times.

i. Subpanel Configuration

Subpanel Configuration will need to be accessed when 
initially setting up your system. This menu allows the user 
to configure the panelboard setups with the unit. This is 
where the number of BCBs per panelboard will be chosen, 
the location of each BCB, and the number of breakers per 
panelboard (9, 18, 30, or 42 where 42 circuit is the default).    

1. Panelboard List ( 1 – 8 )

a. Panelboard Number

Allows the user to specify a unique numerical address 
to associate with the panelboard.

b. Panelboard Name

Allows the user to alter the default 
4-character identifier for the panelboard.

c. Panelboard Type

Allows the user to pick the configuration of the panel-
board being used from the list below.

i.

Left

ii.

Right

iii. Left – 18

iv. Right – 18

v.

Left – 30

vi. Right – 30

vii. Top

viii. Bottom

ix. Top – 9

Содержание Cutler-Hammer Pow-R-Command 750

















Отзывы: