![background image](http://html1.mh-extra.com/html/eaton/ceag-at-s-series/ceag-at-s-series_mounting-and-operating-instructions_3838380050.webp)
50
8 Operating
MANUAL CEAG AUtoMAtiC tEst systEM At-s
+
40071860177 (C) December 2016 www.ceag.de
<ok>
Menu 3.11:
Search substation ...
Group no.: 07
Substation
S1/S2-mode: Slave
S1/S4-mode: -------*
<Menu> finishes the entry and the
following display appears:
Device addresse:01
Version Z410C
ND 00 09 73 72 96 00
Device name
The selection in the second menu serve for the display of the active substations.
Only substations with a programmed group number will be find if not, the message «transmission
failure» appears.
By a selection of «S1/S2-mode: Master - yes» the wohle group can be switched into the mode
«blocked» via the F3-switch of the Master controller. At the Master controller appears the display
«Blocked S1/S2» – at the controllers of the substations appears the message «Blocked LON»
Buzzer setup
Display setup
Timer setup
Substation setup
etc.
Setting options:
S1/S2: Slave or Master or ------
S3/S4: Save or Master or ------
Explanation:
Master: controls slave and other masters
Slave: controlled by master
------: under no control
<ok>
Menu 3.12:
This menu is used to activate and inter-
face the system with a master monitor-
ing device using the CG-S bus or the M3
function.
Line selection (1 / 2) with
Select a device (bus) address (1 ...
32) in line 1 with keys
(display — : no interface)
Select no/yes in line 2 for the option
LON switch with
Line 4: Device name user-definable.
See text assignment 4.2
Finish and return to Menu 3 with
<Menu>
Note:
The entries in lines 3 and 4 are for infor-
mation for the system integrator only.
Device address: 1
LON switch no
NID00 05 94 75 52 00
Device name
Display setup
Timer setup
Substation setup
Connection to BMS
etc.
This menu option can be used to assign
functions to the function keys (F1...F3 on
the control module); the functions are
executed as soon as the relevant key is
pressed.
It is advisable to assign only one function
per key; the star icon goes out when a key
is assigned another function.
Select the function key (1 to 3) with
keys
Highlight the function with
Select the function (
) with <ok>
Finish and return to Menu 3 with
<Menu>
Timer setup
Substation setup
Connection to BMS
Function keys
etc.
<ok>
Menu 3.13:
Function key 1
No function
Switch
Block device
Manual reset
F-Test without lead
Show fault list
Turn off maintained light
Standby light on
Overview:
Main menu
Test & status menu
Block,reset
Basic settings
DLS/TLS Setup
Circuit setup
Luminaire setup
Memory card
Menu 3
Language
Date & time
Functiontest
Delay time mains return
Manual reset
Selective EmgcyOper.
Relay setup
Buzzer setup
Display setup
Timer setup
Substation setup
Connection to BMS
Function keys
Optional inputs
Serialnumber & type
Password protection
Daylight saving time
Service info
Selection of
menu options
with the
keys
<ok>:
confirm selec-
tion
<Menu>: can-
cel and return
to the previous
menu (any
changes
entered are
saved)
<ESC>: cancel
and return to
the previous
menu (any
changes en-
tered are not
saved)
flashing input
prompt