background image

10

Instructional Leaflet 

IB48041

Effective December 2009

Instructions for AMPGARD 400A

medium voltage starter

 

eaton corporatIon

 www.eaton.com

Figure 24. Unsnap Pin Collar

Figure 25. Remove Pin

Figure 26. Remove Three Line-Side and Three Load-Side Bolts  

(Bolt-In Contactor only) 

Isolation switch

The isolation switch consists of a fixed rear portion and a remov-

able front portion. The switch should operate smoothly in both 

directions, with an increase in resistance as the stabs engage the 

controller line fingers. Inspect for any signs of mechanical wear or 

overheating. 
To withdraw the removable portion:

1. 

Remove the three main fuses

2. 

Remove the control plug 

3. 

Remove the cotter pin and clevis pin from drive rod clevis

4. 

Remove the two bolts securing the removable portion of the 

switch to the fixed portion

5. 

Pull the switch forward, then down and out of the controller

 caution

take care not to let the switch quickly Drop Down as the 

removable portion separates from the fixeD portion or  

Damage to the shutter can occur.

Figure 27. Isolation Switch Control Plug

Figure 28. Isolation Switch Drive Rod

Line-Side 

Bolts (3)

Load-Side 

Bolts (3)

Collar

Control  

Plug

Disconnect 

by Removing 

Pin in Clevis

Drive Rod

Содержание Ampgard 400













Отзывы: