background image

Effective December 2009

Instructional Leaflet IB48041

Instructions for AMPGARD 400A

medium voltage starter

 Danger

reaD anD unDerstanD this manual in its  

entirety before installing or operating the 

controller. installation, aDjustment, repair, 

anD maintenance of these controllers  

must be performeD by qualifieD personnel.  

a qualifieD person is one who is familiar  

with the construction anD operation of  

this equipment anD the hazarDs involveD.

Introduction

This instruction book is intended to cover  

the handling, installation, operation, and mainte-

nance of AMPGARD

T

 400A, 7.2 kV starters and 

associated equipment. The function of these  

controllers is to start, stop, and protect medium 

voltage motors, transformers, capacitors, and  

other loads. Controllers may be of full voltage, 

reduced voltage reactor, reduced voltage  

autotransformer, reduced voltage solid-state, or 

two-speed type. They may control induction or  

synchronous machines, and they may be  

non-reversing or reversing.
While this instructional leaflet is dedicated primarily 

to full-voltage starting, the other applications listed 

are an expansion of the principles identified in this 

leaflet. This leaflet does not purport to cover all 

possible contingencies, variations, and details that  

may arise during operation or maintenance of this 

equipment. If further information is desired  

regarding this product, contact your local Eaton 

sales office. 

Identification

A rating nameplate is located on the door of each 

controller. Contained on this nameplate are the  

controller type and ratings as required by industry 

standards. Also contained on this nameplate is the 

factory’s general order number. This number should 

be given to the Eaton sales office if a question 

should arise concerning the equipment or if renew-

al parts are required. Refer to 

Figure 1

 for typical 

location of rating nameplates.

Содержание Ampgard 400













Отзывы: