Eaton 9155 N Скачать руководство пользователя страница 64

Страница: 64 / 99

P-164000341

8-10 kVA, 50/60 Hz (1-phase input) &

8-15 kVA, 50/60 Hz (3-phase input)

Revision 1

User's Guide

9 Maintenance

All operations inside the unit must be performed only by a service engineer from the manufacturer or

from an agent, authorised by the manufacturer.

The troubleshooting procedure gives simple remedial if a malfunction occurs in the UPS. The operator

should start the trouble shooting if there is an active alarm indicated on the LCD screen. Service

should be contacted if the active alarm is abnormal and displayed as a service code.

Call service if you are not able to solve the problem.

LDC display

Description

Action

Overload

The connected load needs more

power than the UPS is rated to pro-

vide. The inverter or static bypass is

supplying the excessive load level.

Shut down the least important load

that is connected to the UPS. The

UPS should switch back to normal

operation once the load level is ac-

ceptable.

Battery test failed

Your batteries are detected to be

faulty.

Batteries should be replaced and

you need to contact the local office

or representative of the UPS manu-

facturer.

Battery low

The UPS is operating in stored en-

ergy mode. It will shut down soon

due to low battery voltage.

Make controlled shutdown of the

protected load immediately to pre-

vent loss of data.

On battery

The UPS is operating in stored en-

ergy mode.

Save your data and perform a con-

trolled shutdown of your server

load.

Overtemperature

High UPS temperature is detected.

Check that fans are operational and

ventilation holes are not blocked.

Make sure the ambient tempera-

ture is not excessive.

Table 9-1: Typical alarms displayed in the LCD screen of the UPS unit

9.1 Regular service/intervals

The UPS requires very little maintenance if installed in an appropriate environment. In order to ensure

maximum availability of the UPS, manufacturer recommends signing a proactive service agreement

with a local authorised service provider.

Maintenance

Interval

Batteries change

~ 3-5 years / service

Batteries test

~ 18 months / service

Содержание 9155 N




































































































Результаты поиска

Содержание 9155 N

Отзывы:

Похожие инструкции для 9155 N

Бренды по названию

Популярные бренды

Eaton 9155 N, Руководство пользователя

Результаты поиска

Содержание 9155 N

Отзывы:

Похожие инструкции для 9155 N

Бренды по названию

Популярные бренды