Eaton 9155 N Скачать руководство пользователя страница 14

Страница: 14 / 99

P-164000341

8-10 kVA, 50/60 Hz (1-phase input) &

8-15 kVA, 50/60 Hz (3-phase input)

Revision 1

User's Guide

3 Mechanical installation

The UPS and accessories are delivered on a specifically designed pallet that is easy to move with a

forklift or a pallet jack. Keep the UPS always in upright position and do not drop the equipment. Do

not either stack the pallets because of high-energy batteries involved and the heavy weight.

3.1 Delivery check

The UPS is delivered with the following items:

• Plastic bag containing:

• User’s Guide, paper format, English language

• UPS Safety Manual, multilingual

• Residual voltage warning stickers

• Software Suite, CD-ROM format, English language

• RS-232 serial cable for the Software Suite

• Delivery documents

3.2 Unpacking and visual inspection

Check that there are no signs of shipping damages. The models higher than 1m are equipped with

'Tip&Tel' indicator. The indicator should be intact if the equipment has been transported in the upright

position.

NOTE

A claim for shipping damage must be filed immediately and the carrier must be informed
within 7 days of receipt of the equipment. The packing materials should be stored for further
investigation.

Before unpacking, use a forklift or pallet jack to move the equipment as close as possible to the

installation site. Unpack the equipment by removing the packing and shipping materials. Make a

visual inspection and check that the inside 'Drop&Tel' indicator is intact. Make sure that the floor

surface is solid and suitable for heavy weight and remove the equipment slowly from the pallet using

lifting belts or other suitable method. Be sure to always lift from the bottom of the unit as the top of

the cabinet is not designed to carry any weight. Discard or recycle the pallet and the other shipping

materials in a responsible manner.

Check the information on the type designation label of the equipment to verify that the unit is of the

correct type. The type designation label includes ratings, a CE marking, a type code, a part number

and a serial number. The serial number is important when making inquiries. It allows individual

recognition of the equipment.

Содержание 9155 N




































































































Результаты поиска

Содержание 9155 N

Отзывы:

Похожие инструкции для 9155 N

Бренды по названию

Популярные бренды

Eaton 9155 N, Руководство пользователя

Результаты поиска

Содержание 9155 N

Отзывы:

Похожие инструкции для 9155 N

Бренды по названию

Популярные бренды