Eaton 9155 N Скачать руководство пользователя страница 26

Страница: 26 / 99

P-164000341

8-10 kVA, 50/60 Hz (1-phase input) &

8-15 kVA, 50/60 Hz (3-phase input)

Revision 1

User's Guide

6.2.3 UPS models with an internal output transformer

Figure 6-4: The location of the power terminals for UPS unit with an internal output
transformer

The installation procedure for models with an internal output transformer is described below.

Remove the cover(s) of the terminal box of the power cables with a screwdriver. In TA models

rectifier input cables are connected to the filter, which is located on top of the unit. Refer to the

dimensional drawing for the correct location of the unit.

Slide the cables through the grommets of the connection box.

Connect the conductors of the rectifier and bypass input cables to the proper terminals. With

single phase unit it is recommended to use the same phases for rectifier and bypass inputs.

Connect the conductors of the load cable to the proper terminals at the back of the

transformer.

Connect the conductors of an external battery cabinet cable to the external b, - and
PE terminals. Check for the correct polarity. See

Chapter 6.3 External Battery Cabinet (EBC)

installation procedure

on page 37.

Содержание 9155 N




































































































Результаты поиска

Содержание 9155 N

Отзывы:

Похожие инструкции для 9155 N

Бренды по названию

Популярные бренды

Eaton 9155 N, Руководство пользователя

Результаты поиска

Содержание 9155 N

Отзывы:

Похожие инструкции для 9155 N

Бренды по названию

Популярные бренды