e2v ELiiXA UC4 Скачать руководство пользователя страница 28

Страница: 28 / 62

ELiiXA® UC8/UC4

Eliixa_Color–revF 04/11

e2v semiconductors SAS 2011

6.3.3

Exposure and Synchronization

•

Synchronisation Mode

Timed or Triggered, it defines how the grabbing is synchronized

This command is

available in the CommCam “Exposure” section :

Read function : “

r sync

”;

Return by the camera:

•

0 : Free Run mode

•

1 : Ext Trig with Integration time set in the Camera

•

2 : Ext Trig with Integration time maximum in the line period

•

3 : Ext ITC (Integration Time Controlled) : The same Trig signal defines the line period
and its low level defines the integration time

•

Ext Trig with two trig signal : CC2 defines the start of the integration and CC2 defines

the Stop of the integration.

Write function : “

w sync

” <value>

Timing Specifications

This table is for all the synchronization modes.

Label

Description

Min

Typ

Max

Effective exposure time duration

1,5 µs

CC1 rising to integration period start delay

0.3 µs

Integration period stop to LINE1 rising set-up time

2.0 µs

CC1 hold time (pulse high duration)

1 / 3 µs

(*)

td1

CC1/CC2 falling/rising to integration period start delay

0.3 µs

td2

CC1/CC2 rising to integration period stop delay

0.3 µs

tcc

CC1 Rising to integration stop delay

3µs

(*)

3µs in ITC Trig Mode, 1µs for the other modes

Содержание ELiiXA UC4































































Результаты поиска

Содержание ELiiXA UC4

Отзывы:

Похожие инструкции для ELiiXA UC4

Бренды по названию

Популярные бренды

e2v ELiiXA UC4, Руководство пользователя

Результаты поиска

Содержание ELiiXA UC4

Отзывы:

Похожие инструкции для ELiiXA UC4

Бренды по названию

Популярные бренды