E.H. Wachs MDSF Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

E.H. Wachs MDSF Скачать руководство пользователя страница 32

FF05

65285

Version conflict:
Object data in the
flash are invalid

Reaction 1: Downramp actual
speed; remain in position
control state.

FF06

65286

No object for process
data; object cannot
be mapped

Reaction 1: Downramp actual
speed; remain in position
control state.

FF07

65287 Data not valid

Reaction 1: Downramp actual
speed; remain in position
control state.

FF08

65288 No convert function

Reaction 1: Downramp actual
speed; remain in position
control state.

Drive needs to be repaired.

FF09

65289 Process data overflow

Reaction 1: Downramp actual
speed; remain in position
control state.

Load IEC project again into device, configure device anew (if needs
be, create new project)

FF10

65296

Command syntax
error

Reaction 1: Downramp actual
speed; remain in position
control state.

Error history, retain variables and absolute positions invalid. Flash
defective? Verify shutdown sequence! New data block is created
and saved with the next shutdown.

FF11

65297 Value not valid

Reaction 1: Downramp actual
speed; remain in position
control state.

Load application data into device (configuration).

FF12

65298 Checksum error

Reaction 1: Downramp actual
speed; remain in position
control state.

Load application data into device (IEC61131-3 program). Turn
device off and back on again.
Update Firmware or adapt IEC program if necessary.
Please use a Compax3 tool release (C3Mgr) higher than R08-1 for
very old devices (firmware V01.xx.yy).

FF13

65299 Timeout error

Reaction 1: Downramp actual
speed; remain in position
control state.

FF14

65300 Overflow error

Reaction 1: Downramp actual
speed; remain in position
control state.

De-energize motor, then perform function

FF15

65301 Parity error

Reaction 1: Downramp actual
speed; remain in position
control state.

FF16

65302 Frame error

Reaction 1: Downramp actual
speed; remain in position
control state.

Find cause: Read objects 25.4 and 25.5

FF17

65303 Gateway Timeout

Reaction 1: Downramp actual
speed; remain in position
control state.

Load configuration into device or avoid WriteFlash command in
cam operation.

FF1A

65306

C3MCom: Wrong
Block-Check-
Character (BBC)

Reaction 1: Downramp actual
speed; remain in position
control state.

FF1B

65307 C3MCom: Timeout

Reaction 1: Downramp actual
speed; remain in position
control state.

Adapt buffer reservation for IEC program (Object 30.2) or download
IEC program again with the C3-Manager.

FF1C

65308 C3MCom: Overrun

Reaction 1: Downramp actual
speed; remain in position
control state.

Check IEC program for objects unknown to the current Firmware.
Maybe the wrong IEC Target was selected (e.g. C3F Target for C3).

FF1D

65309 C3MCom: Parity

Reaction 1: Downramp actual
speed; remain in position
control state.

Check IEC compiler settings and re-compile IEC program if
necessary. Update Firmware if necessary.

FF1E

65310 C3MCom: Frame

Reaction 1: Downramp actual
speed; remain in position
control state.

Configure device again (if needs be, create new project) and load
into device.

«
...
30
31
32
33
34
...
»

Содержание MDSF











































Отзывы:

Нет отзывов